1. Introducció
This manual provides essential information for the safe and efficient operation of your Anern AN-PVI Series Photovoltaic Inverter. Please read this manual thoroughly before installation and use, and keep it for future reference.
Característiques principals:
- Sortida d'ona sinusoïdal pura.
- Vol d'entrada configurabletage range for various applications via LCD settings.
- Compatibilitat amb el volum de la xarxa elèctricatage.
- Automatic restart upon AC recovery.
- Protecció integrada contra sobrecàrregues, sobretemperatura i curtcircuits.
- Funció d'arrencada en fred.
- Dual MPPT for 6KW models and three MPPT for 10KW models.
- Capable of running 3-phase motors: 6KW model supports 3P motors, 10KW model supports 1.5P+3P motors.
- Designed for full load operation using solar power only.
- Protecció d'entrada IP21.
- Maximum conversion efficiency of 97%.
- Important Note: This inverter does not support connection to batteries.
2. Configuració i instal·lació
Proper installation is crucial for the safe and optimal performance of your inverter. Ensure all connections are secure and follow local electrical codes.
2.1 Diagrama del sistema
The following diagram illustrates a typical system setup for the Anern AN-PVI inverter, integrating solar panels, a generator, the utility grid, and various loads, including a water pump system.
2.2 Product Appearance and Connection Points
Familiarize yourself with the inverter's physical layout and connection terminals before proceeding with installation.
- Utility Input: Connects to the main utility grid.
- Photovoltaic Input (PV1, PV2, PV3): Connects to your solar panel arrays. Ensure correct polarity and voltage.
- Utility Output: Connects to your household or facility loads.
- Inverter Switch (ON/OFF): Main power switch for the inverter.
- CT Backflow Prevention Interface: For connecting a Current Transformer (CT) module, if required for grid-tie applications in your region.
- Terminal de cable de terra: Essential for safety grounding.
2.3 Notes prèvies a la instal·lació
- The inverter is designed for direct power conversion and cannot be connected to batteries.
- For PV-only operation (without mains power), the PV voltage must be greater than 150Vdc for the inverter to start.
- When connecting to a water pump, ensure the inverter's power capacity is 5-7 times greater than the water pump's power. This inverter is suitable only for domestic small water pumps.
- If connecting to the grid, ensure your local regulations do not require specific grid connection certifications that this inverter may not possess. A CT module may be required; please consult your supplier.
3. Instruccions de funcionament
Follow these steps for safe and effective operation of your inverter.
3.1 Startup and Shutdown Sequence
- Inici: Always turn on the inverter first, then activate the connected loads.
- Tancament: Always shut down the connected loads first, then turn off the inverter.
3.2 Output Source Priority Configuration
The inverter allows you to configure the priority of power sources for your loads. This setting can typically be adjusted via the LCD interface.
- Utility First (Default): The inverter will prioritize power from the utility grid to supply the loads. Solar power will only be used to power the loads when utility power is unavailable.
- Solar Primer: Solar energy is the primary power source for the loads. If solar energy is insufficient to power all connected loads, the utility grid will supply power simultaneously. If both solar energy and utility power are unavailable, or if solar energy is insufficient and utility power is not available, the loads will not receive power.
3.3 Configuració LCD
The inverter features an LCD display for monitoring system status and configuring various parameters, including the input voltagGamma per a electrodomèstics i ordinadors personals.
Refer to the on-screen menu for navigation and adjustment of settings.
4. Manteniment
Regular maintenance ensures the longevity and reliable performance of your inverter.
- Neteja: Mantingueu l'exterior de l'inversor net i lliure de pols i deixalles. Feu servir un drap sec i suau per netejar-lo. No utilitzeu netejadors líquids.
- Ventilació: Ensure that the ventilation openings are clear and unobstructed to prevent overheating.
- Connexions: Periodically check all electrical connections (PV input, AC input, AC output, ground) for tightness and signs of corrosion.
- Condicions ambientals: The inverter has an IP21 ingress protection rating, meaning it is protected against solid objects over 12.5mm and vertically falling drops of water. Avoid exposing the inverter to direct water spray or harsh weather conditions.
5. Solució De Problemes
Aquesta secció ofereix orientació per a problemes comuns. Per a problemes complexos, poseu-vos en contacte amb personal de servei qualificat.
| Problema | Causa possible | Solució |
|---|---|---|
| Inverter does not start with PV power only. | PV voltage is below the minimum required (150Vdc). | Ensure PV voltage is above 150Vdc. Check solar panel connections and sunlight conditions. |
| L'inversor s'apaga inesperadament. | Overload, over-temperature, or short circuit detected. | Reduce connected load, check for obstructions to ventilation, inspect wiring for short circuits. Allow inverter to cool down before restarting. |
| Loads not receiving power. | Incorrect startup/shutdown sequence, insufficient solar/utility power, or inverter fault. | Follow correct startup sequence (inverter ON, then loads ON). Check power source availability (solar, utility). Verify output source priority setting. |
| Attempting to connect batteries. | Misunderstanding of inverter capabilities. | This inverter model does not support battery connections. Do not attempt to connect batteries. |
6. Especificacions
Detailed technical specifications for the Anern AN-PVI-6000W and AN-PVI-10000W models.
| Paràmetre | AN-PVI-6000W | AN-PVI-10000W |
|---|---|---|
| General | ||
| Model | AN-PVI-6000W | AN-PVI-10000W |
| Potència nominal | 6KVA/6KW | 10KVA/10KW |
| Fase | Entrada trifàsica / sortida trifàsica | |
| PV Input (DC) - Grid-Tie Operation | ||
| Potència màxima d'entrada fotovoltaica | 4500 W * 2 | 4500 W * 3 |
| Vol de CC màximtage | 500Vdc | |
| Inici Voltage / Alimentació inicial Voltage | 90 Vdc / 120 Vdc | |
| MPPT Voltage Rang | 60Vdc | |
| Nombre de rastrejadors MPP / Corrent d'entrada màxim | 2/18A | 3/18A |
| Grid Output (AC) | ||
| Volum de sortida nominaltage | 220/230 / 240VAC | |
| Vol. De sortidatage Rang | 184-264.5VAC or 195.5-253VAC or 184-264.4VAC (Selectable) | |
| Corrent de sortida nominal | 26A | 43A |
| Factor de potència | >0.99 | |
| Eficiència | ||
| Màxima eficiència de conversió (DC/AC) | 97% | |
| AC Input - Off-Grid Operation | ||
| AC Startup Voltage / Reinici automàtic Voltage | 120-140VAC / 180VAC | |
| Vol d'entrada acceptabletage Rang | 90-280VAC o 170-280VAC | |
| Interval de freqüència | 50Hz/60Hz (detecció automàtica) | |
| Corrent d’entrada de CA màxim | 40A | 50A |
| Física | ||
| Mides (D x W x H) | 360x278x106 mm | 360x310x107 mm |
| Pes net | 4.9 kg | 6.5 kg |
| Interfície | ||
| Funció paral·lela | No | |
| Port de comunicació | RS232 (WIFI), CAN (Parallel) | |
| Medi ambient | ||
| Humitat | 5% a 95% d'humitat relativa (sense condensació) | |
| Grau IP | IP21 | |
| Temperatura de funcionament | -10 ℃ a 50 ℃ | |
| Temperatura d'emmagatzematge | -15 ℃ a 60 ℃ | |
7. Garantia i Suport
For warranty information, terms, and conditions, please refer to the documentation provided at the time of purchase or contact your seller directly. For technical support or service inquiries, please contact Anern customer service or your authorized dealer.
8. Consells d'usuari
- Verify Specifications: Abans de la compraasing or installing, always confirm the exact model specifications (e.g., 6KW vs. 10KW) and physical dimensions to ensure it meets your requirements.
- No Battery Support: Remember that this inverter series is designed for direct power conversion and does not support battery storage. Do not attempt to integrate batteries into the system.
- Grid-Tie and Off-Grid Functionality: The AN-PVI series supports both grid-tie and off-grid operations. Ensure your setup and configuration match your intended use and local regulations.
- Water Pump Sizing: If using with a water pump, ensure the inverter's power rating is significantly higher (5-7 times) than the pump's power for optimal performance and to prevent overload. This inverter is primarily for domestic small water pumps.
