1. Producte acabatview
The SONOFF ZBDongle-P Zigbee 3.0 USB Dongle Plus is a versatile USB stick designed to function as a universal Zigbee gateway. It enables local control of various Zigbee sub-devices through open-source home automation platforms like Home Assistant, utilizing ZHA (Zigbee Home Automation) or Zigbee2MQTT. This eliminates the need for multiple brand-specific Zigbee hubs, offering a unified solution for smart home integration.
The dongle supports a wide array of SONOFF Zigbee devices, including BASICZBR3, S31 Lite zb, SNZB01, SNZB02, SNZB03, SNZB04, ZBMINI, S26R2ZB, and is compatible with many other Zigbee sub-devices from various brands. It can also be flashed with router firmware to extend the Zigbee network range.
2. Contingut del paquet
En obrir el paquet, assegureu-vos que hi hagi tots els elements i que estiguin en bon estat:
- SONOFF ZBDongle-P Zigbee 3.0 USB Dongle Plus
- Antena externa
- Manual d'instruccions (aquest document)
3. Configuració
Follow these steps to set up your ZBDongle-P:
- Connecteu l'antena: Carefully screw the external antenna onto the SMA connector on the ZBDongle-P. Ensure it is securely fastened but do not overtighten.
- Connecta't al dispositiu amfitrió: Insert the ZBDongle-P into an available USB port on your host device (e.g., Raspberry Pi, PC running Home Assistant). For optimal signal range and to avoid interference, it is recommended to use a USB extension cable.
- Configuració del programari: The ZBDongle-P comes pre-flashed with Z-Stack 3.x.0 coordinator firmware. You will need to configure your chosen home automation software (e.g., Home Assistant with ZHA or Zigbee2MQTT) to recognize and use the dongle as a Zigbee coordinator. Refer to the documentation of your specific software for detailed configuration instructions.
- Hardware Flow Control (Advanced): The original firmware for ZBDongle-P does not support hardware flow control. If you flash a custom firmware that supports flow control, you can then enable it by flicking the DIP switch located on the dongle's circuit board.
4. Instruccions de funcionament
Once the ZBDongle-P is set up and recognized by your home automation software, you can begin operating your Zigbee network:
- Dispositius de vinculació: Follow the instructions within your Home Assistant (ZHA) or Zigbee2MQTT interface to put the dongle into pairing mode. Then, activate the pairing mode on your Zigbee sub-devices. The dongle will discover and add them to your network.
- Dispositius de control: After successful pairing, your Zigbee devices will appear in your home automation interface. You can then control them, create automations, and monitor their status.
- Extending Network Range: The ZBDongle-P can also be flashed with router firmware. When configured as a router, it helps extend the mesh network range, improving signal strength and reliability for devices further away from the coordinator.
5. Manteniment
To ensure the longevity and optimal performance of your ZBDongle-P:
- Cura física: The dongle features an aluminum alloy shell, which helps reduce signal interference. Keep the device clean and free from dust. Avoid exposing it to extreme temperatures or moisture.
- Actualitzacions de firmware: Periodically check for updated firmware for the ZBDongle-P. Firmware updates can introduce new features, improve stability, and enhance compatibility. Refer to the official SONOFF resources or the community forums for your chosen home automation platform for information on firmware updates and flashing procedures.
6. Solució De Problemes
If you encounter issues with your ZBDongle-P, consider the following:
- Dongle no reconegut: Try connecting the dongle to a different USB port on your host device. Ensure that the necessary drivers for the CP2102(N) USB-to-serial chip are installed on your operating system.
- Zigbee Devices Not Pairing: Verify that the dongle is in pairing mode and that your Zigbee devices are also in their respective pairing modes. Ensure the devices are within range of the dongle or a Zigbee router.
- Problemes de senyal: If you experience poor signal strength or dropped devices, try using a USB extension cable to move the dongle away from the host device, which can reduce interference. Ensure the antenna is securely attached.
- Control de flux: If you are using custom firmware that requires hardware flow control, ensure the DIP switch on the dongle is set correctly after flashing the firmware. The original firmware does not utilize hardware flow control.
7. Especificacions
| Característica | Detall |
|---|---|
| Model | ZBDongle-P |
| Entrada | 5 V CC (100 mA màx.) |
| Temperatura de treball | -10 ℃ ~ 40 ℃ |
| Protocol sense fils | Zigbee 3.0 |
| Material de closca | Aliatge d'alumini |
| Dimensió | 87 x 25.5 x 13.5 mm |
| System on Chip (SoC) | TI CC2652P |
| USB-Serial Chip | CP2102(N) |
| Potència de sortida | 5dBm (default), Max 20dBm |
| Certificació | CE, FCC |
8. Consells d'usuari
- Cable d'extensió USB: Always consider using a USB extension cable (1.5m is often recommended) to physically separate the dongle from your host device. This can significantly improve Zigbee signal quality by reducing interference from the host's electronics.
- Firmware Customization: The ZBDongle-P is highly customizable. Many users flash alternative firmware (e.g., from Koenkk or other community developers) to enable features like hardware flow control or to convert the dongle into a Zigbee router for network expansion. Research these options carefully before proceeding.
- Suport comunitari: For advanced configurations, troubleshooting, or specific platform integrations (Home Assistant, Zigbee2MQTT), leverage the extensive online communities. These resources often provide detailed guides and solutions.
9. Garantia i Suport
Per obtenir informació sobre la garantia i assistència tècnica, consulteu la pàgina oficial de SONOFF. weblloc web o contacteu directament amb el venedor. Conserveu el rebut de compra com a comprovant de compra.
