Yinuogo YNG306 433.42MHz Garage Remote Control User Manual

1. Introducció

The Yinuogo YNG306 is a 433.42MHz rolling code garage remote control designed for compatibility with specific garage door opener models, including TR2 and TR4 series. This remote offers a convenient and reliable solution for replacing lost or damaged original remotes, ensuring seamless operation of your garage door. It features two buttons for intuitive control and comes with an included battery for immediate use.

2. Especificacions

3. Configuració i programació

This remote control requires programming with your garage door opener's receiver. Ensure you have access to your receiver/control box before proceeding.

General Programming Steps (Common Receiver Types)

1. Localitza el receptor: Open the control box of your garage door motor. The receiver board is typically found inside, next to the motor.
2. Activa el mode d'aprenentatge: Press the 'PROG' or 'RF Learning' button on the receiver board. An LED indicator on the receiver will usually light up, indicating it's in learning mode.
3. Programa el comandament a distància: While the receiver's LED is lit, press the desired button on your new YNG306 remote control. The receiver's LED will typically flash and then turn off, confirming successful programming.
4. Espera: Wait approximately 10 seconds for the programming to finalize.
5. Prova: Test your new remote control to ensure it operates the garage door correctly.

Visual Aid for PROG Button Location:

Example of a receiver board with the 'PROG Button / RF Learning' clearly marked.

Un altre example showing the 'PROG Button / RF Learning' on a different receiver model.

A third example illustrating the 'PROG Button / RF Learning' on a receiver board.

Specific Programming for Axroll Receiver Type (Fig. 2)

1. Access Receiver: Open the housing of your receiver, located next to the motor.
2. Menú de navegació: On the receiver board, use the arrow keys until "P8" appears on the screen.
3. Confirmeu la configuració: After one second, the setting "0.0" should appear, indicating the gate open/close function.
4. Inicia l'aparellament: Simultaneously press the button you wish to program on your new remote control AND the "+" button on the receiver for 3 seconds. Three dashes will appear on the screen.
5. Release Buttons: Deixeu anar els dos botons.
6. Finalitzar: Wait 10 seconds. Your new remote control is now programmed.

Diagrams illustrating programming steps for different receiver types (Fig. 1 and Fig. 2).

Producte acabatview Vídeo:

4. Instruccions de funcionament

Once successfully programmed, operating your YNG306 remote control is straightforward:

1. Per obrir/tancar: Press either button A or button B on the remote control. The garage door will respond accordingly.
2. Stopping Movement: Press the active button again to stop the garage door mid-movement, if your opener supports this feature.

The YNG306 remote control, ready for use.

5. Manteniment

Canvi de bateria

The YNG306 remote control uses a standard coin cell battery (typically CR2032). If the remote's LED indicator does not light up or its range significantly decreases, it's likely time to replace the battery.

1. Obriu el Casing: Carefully pry open the remote control casing using a small flat-head screwdriver or a similar tool. Look for a small notch or seam along the edge.
2. Treure la bateria antiga: Gently remove the old battery from its compartment. Note its orientation (+/- sides).
3. Inseriu una bateria nova: Inseriu una nova bateria CR2032 amb la polaritat correcta.
4. Tanca Casing: Enganxa el comandament a distància casintorneu a unir-se de manera segura.

Atenció General

• Mantingueu el comandament a distància sec i allunyat de la humitat.
• Eviteu exposar el comandament a distància a temperatures extremes.
• Netegeu el comandament a distància amb un drap suau i sec. No utilitzeu productes químics agressius ni netejadors abrasius.
• Eviteu deixar caure el comandament a distància, ja que això pot danyar els components interns.

Davant i darrere view of the YNG306 remote, showing its compact design.

6. Solució De Problemes

• El comandament a distància no funciona després de la programació: Double-check that the programming steps were followed precisely. Ensure the receiver was in learning mode and the correct button was pressed on the remote.
• El LED del control remot no s'il·lumina: The battery may be dead or incorrectly inserted. Replace the battery following the maintenance instructions.
• Rang de funcionament limitat: This could indicate a low battery. Also, check for potential sources of radio interference near the garage door opener or the remote control.
• Garage door not responding: Ensure the garage door opener itself is powered on and functioning correctly. If other remotes work, the issue is likely with the YNG306 remote's programming or battery.

7. Consells d'usuari

• Keep Original Remote: If you are replacing a lost remote, consider keeping any remaining original remotes as a backup or for reference during programming.
• Note Down Steps: It can be helpful to write down the specific programming steps for your receiver model for future reference, especially if you need to re-program or add more remotes.
• Interval de prova: After programming, test the remote's range from various distances and angles to ensure optimal performance.

8. Garantia i Suport

This Yinuogo remote control comes with a 1-year warranty from the store. For any product-related inquiries, technical assistance, or warranty claims, please contact the seller directly through your purchase platform. They will be able to provide specific support and guidance.