Miboxer FUT020 RGB LED Controller Instruction Manual

1. Introducció

The Miboxer FUT020 is a DC12-24V 2.4GHz RF RGB LED Controller designed for controlling RGB LED strips and FCOB lighting. It offers brightness and saturation control, allowing for a wide range of color adjustments and dynamic lighting effects. This manual provides detailed instructions for the proper installation, operation, and maintenance of your FUT020 controller.

2. Especificacions

2.1. LED Controller (FUT020)

• Núm. de model: FUT020
• Entrada Voltage: DC12-24V
• Sortida: 6A/Channel (3 circuits: R/G/B)
• Resultat total: Màxim 10 A
• RF: 2.4 GHz
• Distància de control: 30 m (espai sense barreres)
• Temperatura de treball: -10~40°C
• Connexió de sortida: Ànode comú
• Dimensions: L85mm * W45mm * H22mm
• Material: ABS

2.2. Remote Control (FUT020)

• Núm. de model: FUT020
• Voltage: 3 V (2 piles AAA)
• Consum d'energia en espera: <20µA
• Potència de transmissió: 6dBm
• RF: 2.4 GHz
• Distància de control: 30 m (espai sense barreres)
• Freqüència de transmissió: 2400-2483.5 MHz
• Mètode de modulació: GFSK
• Temperatura de treball: -10~40°C
• Material de la coberta: ABS

3. Configuració

3.1. Controller Wiring

Ensure all power is disconnected before wiring. Connect the LED strip to the controller and the power supply to the controller as shown in the diagram below. The controller uses a common anode connection method.

3.2. Instal·lació de la bateria del control remot

The remote control requires 2 AAA batteries. Open the battery compartment on the back of the remote and insert the batteries, ensuring correct polarity.

3.3. Matching Remote Control to Receiver

Typically, the remote control and receiver are pre-matched from the factory. If re-matching is needed:

1. Assegureu-vos que el controlador estigui apagat.
2. Enceneu el controlador.
3. Within 3 seconds of powering on, press Key 4 (Turn Up/Brightness/Speed) once.
4. The connected LED light will blink 3 times, indicating successful matching.

3.4. Clearing Code

To clear the matching code from the receiver:

1. Assegureu-vos que el controlador estigui apagat.
2. Enceneu el controlador.
3. Within 3 seconds of powering on, press Key 4 (Turn Up/Brightness/Speed) five times.
4. The connected LED light will blink 6 times, indicating successful code clearing.

4. Instruccions de funcionament

The FUT020 remote control features a user-friendly interface for various lighting adjustments.

4.1. Funcions clau

• Key 1 (ON/OFF): Turns the LED lights on or off.
• Key 2 (Light Changing Mode): Activates and cycles through 15 different dynamic lighting modes.
• Key 3 (Color Light/White Light Switching Mode): Toggles between color mode and white light mode.
• Key 4 (Turn Up): Increases brightness or speed of dynamic modes.
• Key 5 (Turn Down): Decreases brightness or speed of dynamic modes.
• Anell de color: Touch the color ring to select any desired color.

4.2. Com utilitzar

1. Encès/apagat: Press Key 1 to turn the lights on or off.
2. Modes dinàmics: Press Key 2 to activate the light changing mode. Keep pressing Key 2 to cycle through the 15 available programs.
3. Mode de llum blanca: Press Key 3 once to activate the pure white light mode. Adjust the brightness using Key 4 (up) or Key 5 (down).
4. Selecció de color: Press Key 3 twice to activate the color ring. You can then select any color by touching the color ring. Adjust the brightness using Key 4 (up) or Key 5 (down).
5. Funció de reprendre: The controller will remember the last setting and resume it when powered on again.

4.3. Dynamic Mode Chart (Key 2)

The following table details the 15 dynamic modes available via Key 2:

5. Manteniment

5.1. Remote Control Sensitivity

To maintain the sensitivity of the color ring, avoid touching or pressing it while loading the batteries. After installing batteries, wait approximately 3 seconds before using the remote controller. If the color ring becomes unresponsive, try reloading the batteries.

5.2. Neteja

Wipe the controller and remote control with a soft, dry cloth. Do not use harsh chemicals or abrasive cleaners.

6. Solució De Problemes

• Lights not responding to remote:
  1. Check if the remote control batteries are correctly installed and have sufficient power. Replace if necessary.
  2. Ensure the remote is matched to the receiver. Follow the 'Matching Remote Control to Receiver' steps in Section 3.3.
  3. Verify that the controller is receiving power and the LED strip is correctly wired.
• Color ring not sensitive:
  1. Reload the batteries in the remote control.
  2. Wait 3 seconds after battery installation before attempting to use the color ring.
• Unexpected light behavior:
  1. Try clearing the remote's code and re-matching it to the receiver (Section 3.4 and 3.3).
  2. Ensure the correct mode is selected (color light, white light, or dynamic mode).

7. Consells d'usuari

• For optimal performance, ensure the controller is installed in a well-ventilated area to prevent overheating.
• Keep the remote control within the specified 30m barrier-free range for reliable operation. Obstacles can reduce this range.
• When experimenting with dynamic modes, use the speed adjustment (Key 4/5) to find the perfect pace for your ambiance.

8. Garantia i Suport

8.1. Garantia

This Miboxer FUT020 controller comes with a 1-year warranty from the date of purchase, covering manufacturing defects. Please retain your proof of purchase for warranty claims.

8.2. Certificacions

The product is certified with CCC, CE, EMC, FCC, LVD, ROHS, and UL standards, ensuring compliance with relevant safety and quality regulations.

8.3. Suport tècnic

For technical assistance or further inquiries, please contact your retailer or the Miboxer customer support. Refer to the product packaging or Miboxer's official weblloc per obtenir dades de contacte.