Introducció
This manual provides detailed instructions for the setup, operation, and maintenance of your Beninca TO.GO 2WP fixed code remote control. This device is designed for controlling compatible Beninca garage doors and gates operating at a frequency of 433.92MHz.
Imatge: Frontal view of the Beninca TO.GO 2WP remote control.
Especificacions
| Característica | Detall |
|---|---|
| Model | Beninca TO.GO 2WP |
| Freqüència | 433.92 MHz |
| Tipus de codi | Codi fix |
| Nombre de botons | 2 |
| Bateria | Inclòs |
| Dimensions (L x A x A) | 70 mm x 40 mm x 6 mm |
| Pes | 0.035 kg |
| Origen | Xina continental |
| Certificació | CE |
| Models compatibles | Beninca TO.GO 2WP, Beninca TO.GO 4WP |
Important: Access to your receiver/opener is required for programming. Please ensure you have this access before attempting to program the remote.
Image: Diagram showing the dimensions of the remote control.
Contingut del paquet
- 1 x Beninca TO.GO 2WP Remote Control
- 1 x bateria (preinstal·lada)
- 1 x Clauer
Configuració i Programació
Follow these steps to program your new Beninca TO.GO 2WP remote control.
Step 1: Clear the Programmer's History
- Press buttons A and B continuously until the LED flashes 3 times.
- Release button B (while continuing to press button A).
- Press button B slowly for 3 times. The LED will flash 3 times.
- Release button A. The history is now cleared.
Step 2: Programming Code from Original Transmitter
- Place the new remote control (programmer) as close as possible to your original Beninca transmitter.
- Press and hold button A on your original transmitter.
- While still holding button A on the original transmitter, press and hold button A on the new remote control (programmer).
- Continue holding both buttons until the LED on the new remote control blinks.
- Release both buttons. The code for button A is now programmed.
- Repeat the process for button B, if desired, using button B on both the original and new remote controls.
Funcions del botó:
- Botó A: Lock / Open
- Botó B: Unlock / Close
Image: Demonstrating pressing a button on the remote control.
Funcionament
Once programmed, your Beninca TO.GO 2WP remote control is ready for use.
- To activate your garage door or gate, simply press the corresponding programmed button (A or B) on the remote control.
- The LED indicator on the remote will light up when a button is pressed, indicating that a signal is being transmitted.
- Ensure you are within range of your receiver for successful operation.
Image: Remote control in use, opening a garage door.
Manteniment
Canvi de bateria
The remote control comes with a pre-installed battery. If the remote's range decreases significantly or the LED indicator does not light up when a button is pressed, it may be time to replace the battery.
- Localitzeu el compartiment de la bateria a la part posterior del comandament a distància.
- Carefully open the compartment using a small screwdriver or coin.
- Traieu la bateria antiga i introduïu-ne una de nova, assegurant la polaritat correcta.
- Tanqueu el compartiment de la bateria de manera segura.
Cura i emmagatzematge
- Mantingueu el comandament a distància sec i allunyat de la humitat.
- Avoid exposing the remote to extreme temperatures or direct sunlight for prolonged periods.
- No deixeu caure el comandament a distància ni el sotmeteu a impactes forts.
- Netegeu el comandament a distància amb un drap suau i sec. No utilitzeu productes químics agressius ni netejadors abrasius.
Resolució de problemes
- Remote not programming:
- Ensure the new remote is placed as close as possible to the original transmitter during programming.
- Verify that the original transmitter is functioning correctly.
- Check the battery in the new remote. A low battery can prevent successful programming.
- Confirm that your receiver/opener is compatible with fixed code 433.92MHz remotes and that you have access to its programming function.
- El comandament a distància no funciona després de la programació:
- Re-attempt the programming steps carefully.
- Ensure the remote's history was cleared correctly before programming.
- Comproveu la bateria.
- Verify that the remote is within the operating range of your garage door/gate receiver.
- L'indicador LED no s'il·lumina:
- The battery may be dead or low. Replace the battery.
- Assegureu-vos que els botons estiguin premuts fermament.
Consells per a l'usuari
No hi ha consells específics per a l'usuari disponibles a partir dels recursos proporcionats.views or Q&A content at this time.
Garantia i Suport
This product is manufactured by Shenzhen Scimagic Development Technology Co.Ltd.
For technical support or warranty inquiries, please refer to the contact information provided by your retailer or the manufacturer's official weblloc.
Adreça del fabricant: Honghai Gebu Building 2301, Baoan Road, Songgang Baoan District Shenzhen Guangdong China.
The product is CE certified, indicating compliance with European health, safety, and environmental protection standards.
Podeu descarregar un manual d'usuari en format PDF: View Manual d'usuari (PDF)
Producte multimèdia
Producte acabatview Vídeo
Video: A short demonstration of the Beninca TO.GO 2WP remote control, showcasing its physical appearance and button functionality.
Imatges addicionals del producte
