1. Introducció
This manual provides essential information for the safe and effective installation, operation, and maintenance of the SMC MBB80-10TZ-DNX0514 Power Assisted Robotic Arm Brake Cylinder. This device is designed for use in industrial automation systems, specifically for robotic arm applications requiring precise braking and holding capabilities. Please read this manual thoroughly before using the product.
2. Configuració
Proper installation is crucial for the safe and efficient operation of the brake cylinder. It is recommended that installation be performed by qualified personnel.
- Muntatge: Securely mount the brake cylinder to the robotic arm or desired application point using appropriate fasteners. Ensure the mounting surface is flat and rigid to prevent misalignment or stress on the cylinder. Refer to the provided diagrams for mounting hole locations and dimensions.
- Pneumatic Connection: Connect the air supply lines to the designated ports on the cylinder. Ensure all connections are tight and leak-free. Use appropriate fittings and tubing for the specified operating pressure.
- Connexió elèctrica (si escau): If the system includes electrical controls for actuation, connect the control wiring according to the system's electrical schematic. Verify correct polarity and secure all connections.
- Inspecció inicial: Before applying power or pressure, visually inspect all connections and mounting points. Confirm there are no obstructions to the cylinder's movement.
3. Instruccions de funcionament
The SMC MBB80-10TZ-DNX0514 brake cylinder operates by pneumatic pressure to engage or disengage the braking mechanism. Always ensure safety protocols are followed during operation.
- Encès: Ensure the pneumatic air supply is connected and regulated to the specified operating pressure.
- Brake Engagement: When pneumatic pressure is applied (or released, depending on the cylinder's design, typically spring-return for braking), the cylinder will actuate to engage the brake, holding the robotic arm in position.
- Brake Release: To release the brake, apply (or release) pneumatic pressure as per the system design. The cylinder will retract, allowing free movement of the robotic arm.
- Parada d'emergència: In case of an emergency, immediately cut off the air supply and power to the system. The brake cylinder is designed to safely engage the brake in such situations.
Safety Warning: Never attempt to manually override the brake mechanism while the system is under power or pressure. Always ensure the robotic arm is safely supported before performing any maintenance or adjustments.
4. Manteniment
Regular maintenance ensures the longevity and reliable performance of your brake cylinder.
- Inspecció diària: Check for any visible damage, loose connections, or air leaks. Listen for unusual noises during operation.
- Neteja: Keep the exterior of the cylinder clean and free from dust, debris, and corrosive substances. Use a soft, damp drap per netejar. No utilitzeu productes químics agressius.
- Qualitat de l'aire: Ensure the pneumatic air supply is clean, dry, and filtered to prevent contamination of internal components.
- Lubricació: Follow the manufacturer's guidelines for internal lubrication, if required. Many modern pneumatic cylinders are pre-lubricated and do not require additional lubrication during their service life.
- Substitució del segell: If air leaks are detected from the piston rod or end caps, the seals may need replacement. This should be performed by a qualified technician.
5. Solució De Problemes
This section addresses common issues you might encounter with the brake cylinder.
| Problema | Causa possible | Solució |
|---|---|---|
| Brake not engaging/releasing | Insufficient air pressure; blocked air lines; faulty control valve; mechanical obstruction. | Check air supply and regulator settings; inspect air lines for kinks or blockages; verify control valve operation; remove any obstructions. |
| Fugides d'aire | Loose fittings; damaged seals; cracked housing. | Tighten all pneumatic fittings; replace damaged seals (contact support); inspect cylinder body for damage. |
| Erratic movement/operation | Fluctuating air pressure; contamination in air supply; internal wear. | Ensure stable air pressure; check air filter and dryer; contact support for internal inspection. |
| Sobreescalfament | Excessive cycling; improper load; internal friction. | Review application parameters; ensure load is within specifications; contact support. |
6. Especificacions
| Característica | Detall |
|---|---|
| Número de model | MBB80-10TZ-DNX0514 |
| Tipus | Power Assisted Robotic Arm Brake Cylinder |
| Categoria de subministraments de bricolatge | Elèctric |
| Origen | Xina continental |
| Longitud del paquet | 22 cm |
| Amplada del paquet | 22 cm |
| Alçada del paquet | 11 cm |
| Pes del paquet | 3.0 kg |
7. Consells d'usuari
Mentre que un usuari específic reviews or Q&A were not available for this product, general tips for pneumatic cylinders include:
- Always use clean, dry, and regulated air to prevent internal damage and ensure consistent performance.
- Periodically check all pneumatic connections for leaks, as even small leaks can lead to significant energy waste and reduced performance.
- Ensure the cylinder is properly aligned with the load to avoid side loading, which can cause premature wear on seals and bearings.
8. Garantia i Suport
This product is backed by a commitment to quality and customer satisfaction. Key support features include:
- Devolucions gratuïtes: Gaudeix de devolucions gratuïtes en un termini de 90 dies des de la compra.
- Garantia de lliurament: En cas de retard en el lliurament, es pot proporcionar un codi de cupó. Es poden fer reemborsaments si el paquet es perd o els articles es fan malbé durant el transport, o si no es produeix el lliurament en un termini de 30 dies.
For technical assistance, troubleshooting beyond this manual, or warranty claims, please contact the seller, Liu Lan 4 Store Store, directly. Their positive feedback rating of 100.0% indicates a strong commitment to customer service.
