1. Introducció
This manual provides comprehensive instructions for the KING GATES STYLO4K and STYLO2K electric gate remote control. It covers product specifications, compatible models, programming procedures, general operation, maintenance, and troubleshooting tips to ensure safe and effective use of your device.
2. Especificacions
| Atribut | Valor |
|---|---|
| Número de model | YNG164 |
| Marca | KINGGates |
| Freqüència | 433.92 MHz |
| Tipus de codi | Rolling Code |
| Botons | 4 |
| Bateria | Inclòs |
| Interval d'operació | 50m-100m |
| Origen | Xina continental |
3. Models compatibles
This remote control is compatible with the following KING Gates transmitters and systems:
- ESTILO
- STYLO2K*
- STYLO4K*
- DigyPad
- Mio C4
- NowoTX
- NovoDigy series
Nota important:
Access to your receiver/opener is required for programming. Please ensure you have access before attempting to program the remote. The remote control must visually match the original, and your model must be listed above for compatibility.
4. Contingut del paquet
El vostre paquet ha de contenir els elements següents:
- 1 x comandament a distància
- 1 x Manual d'instruccions en anglès
- 1 x bateria (preinstal·lada)
- 1 x Clauer
5. Configuració i programació
To program your new remote control, you will need access to your gate receiver. Follow these steps:
- Locate Your Receiver: Open the housing of your gate receiver, typically found near the gate motor.
- Activa el mode de programació: Press the programming button on the receiver. This button is usually labeled as 'ENR', 'MEMO', or 'PROG'. On some receivers, you may need to hold the button down.
- Confirm Programming Mode: The LED indicator on the receiver will light up or change its state to confirm it is in programming mode.
- Program Remote: Press any button on your new remote control for approximately one second, then release it.
- Confirm Successful Programming: The receiver's LED will change its light pattern or turn off to indicate that the remote has been successfully programmed.
- Sortir del mode de programació: Wait a few seconds for the receiver to automatically exit programming mode.
Enhorabona! El vostre nou comandament a distància ja està programat i llest per utilitzar.
6. Instruccions de funcionament
Once your remote control is successfully programmed, operating your electric gate is straightforward:
- Open/Close Gate: Press the programmed button on your remote control to activate the gate opener. A single press typically initiates the open or close cycle.
- Stop Gate: If your gate is in motion, pressing the button again may stop its movement. Refer to your gate opener's specific manual for exact behavior.
7. Manteniment
To ensure the longevity and reliable performance of your remote control, follow these maintenance guidelines:
- Substitució de la bateria: The remote control comes with a pre-installed battery. If the remote's indicator light dims or its range decreases significantly, it's time to replace the battery. Carefully open the remote's casing (refer to diagrams if available) and replace the old battery with a new one of the same type.
- Neteja: Clean the remote control periodically with a soft, dry cloth. Avoid using harsh chemicals or abrasive materials, which can damage the casing or buttons.
- Emmagatzematge: Store the remote control in a dry place, away from direct sunlight, extreme temperatures, and high humidity.
- Eviteu danys físics: Protect the remote from drops, impacts, and excessive pressure, which can damage internal components.
8. Solució De Problemes
Si teniu problemes amb el comandament a distància, proveu els passos següents per resoldre'ls:
- El comandament a distància no funciona després de la programació:
- Ensure you followed all programming steps correctly. Repeat the programming process carefully.
- Verify that your remote control is compatible with your gate receiver model.
- Check the battery. A low battery might prevent successful programming or operation.
- Rang de funcionament reduït:
- Substituïu la bateria per una de nova.
- Ensure there are no obstructions (e.g., large metal objects, thick walls) between the remote and the receiver.
- Check for sources of radio interference in the vicinity.
- Indicator Light Not Lighting Up:
- The battery may be completely drained or incorrectly inserted. Replace the battery.
- Ensure the remote has not sustained physical damage.
- Gate Not Responding:
- Confirm the gate opener itself is powered on and functioning correctly.
- Check if the remote is still programmed to the receiver. If not, re-program it.
9. Consells d'usuari
- Always verify the compatibility of the remote control with your existing gate opener system before purchase and programming.
- Keep your remote control in a safe and easily accessible location, but out of reach of children to prevent accidental operation.
- If you lose your remote, you can purchase a new one and program it to your receiver, effectively replacing the lost unit.
- Avoid exposing the remote to water or extreme temperatures to prevent damage.
10. Garantia i Suport
For any technical assistance, warranty claims, or further inquiries, please contact the seller or manufacturer directly. Ensure you have your product model number (YNG164) and purchase details available when seeking support.
