GEPRC TAKER F405 HD V3 Flight Controller and ESC User Manual

1. Introducció

This manual provides essential information for the installation, configuration, and operation of the GEPRC TAKER F405 HD V3 Flight Controller and its compatible 4-in-1 Electronic Speed Controllers (ESCs): the H65_8S_BLS 65A and H60_BLS 60A. These components are designed for high-performance FPV drone applications, offering advanced control and power management.

Please read this manual thoroughly before attempting to install or operate the components to ensure proper functionality and safety.

2. Especificacions

2.1. GEPRC TAKER F405 HD V3 Flight Controller

Imatge: Superior view of the GEPRC TAKER F405 HD V3 Flight Controller, showing the USB-C port and various solder pads.

2.2. GEPRC TAKER H65_8S_BLS 65A 4IN1 ESC

Imatge: Anglesa view of the GEPRC TAKER H65_8S_BLS 65A 4IN1 ESC.

2.3. GEPRC TAKER H60_BLS 60A 4IN1 ESC

Imatge: Superior view of the GEPRC TAKER H60_BLS 60A 4IN1 ESC.

3. Contingut del paquet

3.1. GEP-F405-HD V3 Flight Controller Package

Image: Contents of the Flight Controller package, including cables and mounting hardware.

• 1 controlador de vol
• 1 x Cable adaptador per a la unitat DJI Air
• 1 x Cable adaptador de controlador de vol
• 4 femelles de niló
• 4 ullets de silicona
• 2 x sh1.0 4-pin ribbon cable
• 1 x Cable de connexió de la càmera

3.2. 4IN1 ESC Package (H65_8S_BLS 65A and H60_BLS 60A)

Image: Contents of the 4IN1 ESC package, including capacitor, cables, and anti-shake pads.

• 1 x ESC
• 1 condensador
• 1 x Cable adaptador de controlador de vol
• 1 cable d'alimentació XT60
• 4 x Silicone anti-shake pads

4. Configuració i instal·lació

Proper installation is crucial for the performance and safety of your FPV drone. This section provides general guidance. For detailed wiring diagrams and specific connection points, please refer to the official GEPRC product page or Betaflight documentation for your specific build.

4.1. Mounting the Flight Controller and ESC

• Mount the Flight Controller (FC) and ESC using the provided silicone grommets and nylon nuts. The silicone grommets are essential for vibration isolation, which helps the gyroscope (IMU) perform accurately.
• Ensure the FC is oriented correctly according to your Betaflight configuration.
• The mounting holes are 30.5x30.5mm. The φ4mm holes become φ3mm after using the silicone shock-absorbing rings.

4.2. Connexions de cablejat

The GEPRC TAKER F405 HD V3 FC features direct plugging into DJI Air Units, simplifying connections for digital FPV systems. The ESCs connect to the FC via a dedicated adapter cable.

• Connexió d'alimentació: Connect the XT60 power cable from the ESC to your LiPo battery. Ensure correct polarity. The FC receives power from the ESC.
• Connexions del motor: Solder your drone motors to the designated motor pads (M1-M4) on the 4-in-1 ESC. Ensure correct motor order and rotation direction as per your frame and Betaflight configuration.
• FC to ESC Connection: Use the provided Flight Controller Adapter Cable to connect the FC to the 4-in-1 ESC. This cable typically carries motor signals, telemetry, and power.
• DJI Air Unit Connection: Utilize the dedicated DJI Air Unit Adapter Cable for direct connection to your DJI Air Unit. This simplifies wiring for video, control, and OSD data.
• Connexió de la càmera: Use the provided camera connection cable for your FPV camera.
• Connexió del receptor: Connect your RC receiver to the appropriate UART on the FC. Refer to the FC's pinout diagram for specific UART assignments.
• Instal·lació de condensadors: Solder the provided capacitor to the main battery pads on the ESC. This helps filter electrical noise and protect the ESC from voltage pics.

Warning: Incorrect wiring can cause permanent damage to your components. If unsure, consult detailed wiring diagrams or seek professional assistance.

5. Instruccions de funcionament

5.1. Firmware Flashing and Configuration

• Betaflight: Connect the Flight Controller to your computer via the Type-C USB interface. Use the Betaflight Configurator software to flash the latest GEPRCF405 firmware target.
• Configuració inicial: Perform initial setup in Betaflight, including sensor calibration (accelerometer, gyroscope), motor testing, receiver configuration, OSD settings, and flight mode assignments.
• Firmware de l'ESC: The ESCs use the B_X_30 target. If necessary, update the ESC firmware using BLHeli_S or BLHeli_32 configurator (depending on the specific ESC variant, though BLS typically implies BLHeli_S).

5.2. Comprovacions prèvies al vol

• Verify all connections are secure and correctly oriented.
• Check motor rotation direction in Betaflight.
• Confirma que l'entrada del receptor estigui registrada correctament a Betaflight.
• Ensure propellers are installed correctly and securely.
• Perform a range check of your radio control system.

5.3. Operació de vol

Once configured and checked, your drone is ready for flight. Always operate in a safe environment, away from people and obstacles. Start with gentle maneuvers to confirm stability and control response.

6. Manteniment

• Inspecció periòdica: Periodically inspect all solder joints and connections for signs of wear, corrosion, or damage.
• Neteja: Keep the FC and ESC clean from dust, dirt, and moisture. Use compressed air or a soft brush for cleaning. Avoid using liquids directly on the electronics.
• Actualitzacions de firmware: Regularly check for and apply firmware updates for both the Flight Controller (Betaflight) and ESCs (BLHeli_S/32) to benefit from performance improvements and bug fixes.
• Vibració Dampening: Ensure the silicone grommets are in good condition and effectively dampening vibrations to the FC's IMU. Replace if they show signs of degradation.

7. Solució De Problemes

• Sense energia: Check battery connection, XT60 cable, and main power pads on the ESC for proper soldering and continuity.
• FC no es connecta a Betaflight: Ensure correct USB cable is used (Type-C), drivers are installed, and Betaflight Configurator is up to date. Try a different USB port or cable.
• Motors que no giren: Verify motor connections, ESC calibration, and motor output settings in Betaflight. Check for bent motor shafts or damaged propellers.
• Vol inestable: Re-check FC mounting for vibration isolation. Ensure IMU calibration is performed. Review PID settings in Betaflight.
• Video Issues (DJI Air Unit): Confirm DJI Air Unit adapter cable is securely connected. Check for interference or damaged video cables.
• L'OSD no es mostra: Verify OSD settings in Betaflight. Ensure camera and video transmitter are correctly connected.

8. Consells d'usuari

• Always use a smoke stopper during initial power-up after assembly to prevent damage from short circuits.
• Keep your Betaflight and ESC firmware updated for optimal performance and access to new features.
• Utilize the onboard 16M Black Box for flight log analysis to fine-tune PID settings and diagnose flight issues.
• The integrated barometer can be useful for altitude hold features, ensure it's not obstructed or exposed to direct prop wash.
• Pay close attention to the mounting instructions, especially using the silicone shock-absorbing rings, to minimize gyro noise.

9. Garantia i Suport

For warranty information, technical support, or further assistance, please refer to the official GEPRC weblloc web o poseu-vos en contacte amb el vostre distribuïdor. Conserveu el comprovant de compra per a qualsevol reclamació de garantia.