AOLON W3002 Microcomputer Temperature Controller
Especificacions tècniques
| Especificació | Detalls |
|---|---|
| Nom del producte | Microcomputer Temperature Controller (XH-W3002) |
| Interval de mesura | -50°C to 110°C (-50°C to 100°C model variation) |
| Interval de control | -50°C to 110°C (-50°C to 100°C model variation) |
| Precisió de la mesura de la temperatura | ±0.2 °C |
| Precisió del control de temperatura | ±0.1 °C |
| Entrada de mesura | NTC10K L=1m waterproof probe |
| Input Power Options | 12V / 24V / 220V AC/DC |
| Opcions de potència de sortida | 120W (12V) / 240W (24V) / 1500W (220V) |
| Tipus de sortida | Sortida directa |
| Capacitat de sortida | Màxim 10 A |
| Distància del forat d'instal·lació | 73mm (Hole size: 4mm) |
| Dimensions | 60 mm × 45 mm × 31 mm |
Configuració i ús ràpids
- Connect the temperature sensor: use the supplied NTC10K waterproof probe (L=1m).
- Provide power using one supported option: 12V/24V/220V AC/DC.
- Set start temperature (P0): press the Configuració button to enter the menu (default to P0), press Configuració again, then use Up/Avall to set the desired start temperature.
- Set stop temperature (P1): in the menu, use Up/Avall to select P1, press Configuració again, then adjust with Up/Avall.
- (Optional) Calibrate temperature (P2): select P2, press Configuració to enter calibration, then set the offset value using Up/Avall.
- (Optional) Set delayed start (P3): select P3 and set the delay time (minutes) using Up/Avall (recommended 3–6 minutes for compressor-based refrigeration; otherwise leave at 0).
Wiring Diagrams & Safety Information
12V / 24V Connection Way
Avís: 12V/24V power supplies must use a stable DC power source.
220V Connection Way
Avís: This model is designed with direct output power. Exercise extreme caution when connecting the electricity. Ensure the load is connected to the output terminal port before powering up to prevent potential output short circuit ignition or sparks.
Settings Parameter Menu
| Codi | Descripció | Interval de configuració | Per defecte de fàbrica |
|---|---|---|---|
| P0 | Temperatura inicial | -50 a 110 °C | 00 °C |
| P1 | Atura la temperatura | -50 a 110 °C | 00 °C |
| P2 | Correcció de temperatura | -10 a 10 °C | 0 °C |
| P3 | Delay to start | De 0 a 10 minuts | 0 minuts |
Parameter Configurations & Functions
P0: Start-up Temperature Setting
Premeu el botó Configuració button to enter the internal menu. The display will default to P0. Premeu el botó Configuració button once more, then use the Up i Avall buttons to set your desired start temperature.
Premeu el botó Configuració button to enter the internal menu. When
P0 is displayed, use the Up or Avall botons per seleccionar P1. Premeu el botó Configuració button again, and adjust the target stop temperature using the Up i Avall botons.Premeu el botó Configuració button to enter the internal menu, then switch to
P2 utilitzant el Up or Avall botons. Premeu el botó Configuració button again to calibrate. Use the Up i Avall buttons to enter the offset value.Calibration Formula: Detected Temperature + Calibration Temperature = Actual Temperature
- If the detected temperature is 0.5°C higher than the actual temperature: Set P2 to -0.5°C
- If the detected temperature is 1.0°C lower than the actual temperature: Set P2 to 1.0 °C
P3: Delayed Start Setting
Premeu el botó Configuració button to enter the internal menu and switch to P3 utilitzant el Up or Avall botons. Premeu el botó Configuració button again and set the delay time in minutes using the Up or Avall botons.
Nota: This function is typically used for compressor-based refrigeration systems (like refrigerators or freezers) to protect the motor. A delay of 3 to 6 minutes is recommended. If you are not controlling a compressor, leave this set to 0.
Modes de funcionament
Mode de calefaccióRegla:Start-up Temperature (P0) < Stop Temperature (P1) The system automatically determines it is in heating mode when P0 is configured lower than P1.
Exampl'escenari:
Control a water heater to turn off when the temperature reaches 50°C and restart heating when the temperature drops back down to 40°C.
- Verify that the heating rule is met: Start-up (40°C) is less than Stop (50°C).
- Premeu el botó Configuració button, enter the menu, select
P0, and adjust the value to 40 °C. - Premeu el botó Configuració button, enter the menu, select
P1, and adjust the value to 50 °C.
Mode de refrigeracióRegla: Start-up Temperature (pø) > Stop Temperature (Pl). The system automatically determines it is in cooling mode when P0 is configured higher than P1.
Exampl'escenari:
Control a cabinet radiator to turn on when temperatures reach 30°C and stop cooling once the temperature drops to 26°C.
- Verify that the cooling rule is met: Start-up (30°C) is greater than Stop (26°C).
- Premeu el botó Configuració button, enter the menu, select
P0, and adjust the value to 30 °C. - Premeu el botó Configuració button, enter the menu, select
P1, and adjust the value to 26 °C.
Resolució de problemes
Common Fault: Incorrect Settings
If you set your temperature values upside down (e.g., configuring heating parameters with P0 > P1), the output indicator light will remain off and the connected load will not work. Check the temperature values in your P0 i P1 settings if the system is unresponsive.
With the controller powered on, press and hold both the Up i Avall buttons simultaneously for approximately 3 seconds. Once the digital tube displays
888, The controller will automatically return to real-time temperature detection, indicating a successful factory reset.- Display “LLL”: Indicates a temperature sensor probe failure. Please inspect, repair, or replace the waterproof probe.
- Display “HHH”: Indicates that the ambient temperature has exceeded the controller’s detection range. Relocate the unit to an appropriate environment.
Documents/Recursos
 | W3002 Microcomputer Temperature Controller |
Referències
- Manual d'usuarimanual.tools