1. Producte acabatview
SEM COLOR COAT is a specialized flexible coating designed to restore or change the color of most vinyl surfaces, flexible and rigid plastics, carpet, and velour. This product is formulated to be fade-resistant, flexible, and provides a permanent finish. It is not a dye, but a coating that adheres to the surface.
An image of the SEM COLOR COAT aerosol can, displaying the product name, model number 15363 (Portola Red), and key features such as flexible coating for vinyl, plastics, carpet, and velour. Important safety warnings regarding flammability and harmful vapors are also visible.
2. Informació de seguretat
PERILL: Aquest producte és un AEROSOL EXTREMADAMENT INFLAMABLE. The pressurized container MAY BURST IF HEATED. Ho és NOCIU O FATAL EN CAS D'ENGLOCAMENT. Vapors are NOCIU. Causes SERIOUS EYE IRRITATION i IRRITACIÓ DE LA PELL.
Always read and follow all cautions on the back panel of the product container before use. Ensure adequate ventilation during application. Wear appropriate personal protective equipment, including gloves and eye protection.
3. Preparació de la superfície
Proper surface preparation is critical for optimal adhesion and durability of the COLOR COAT. Follow these steps:
- Netegeu la superfície: Thoroughly clean the surface to be coated with a suitable cleaner, such as SEM Soap or a comparable automotive-grade cleaner. Remove all dirt, grease, oil, wax, and other contaminants. Rinse thoroughly and allow to dry completely.
- Desgreixar: For best results on vinyl and plastic, follow cleaning with a degreaser like SEM Plastic & Leather Prep or a similar product. This ensures removal of any remaining residues.
- Scuff (if necessary): For rigid plastics, lightly scuff the surface with a fine abrasive pad (e.g., 320-400 grit) to promote adhesion. Clean again after scuffing.
- Emmascarament: Mask off all areas not intended for coating using automotive-grade masking tape and paper.
- Ventilació: Ensure the work area is well-ventilated to prevent vapor accumulation.
4. Application (Operating Instructions)
Follow these instructions for applying SEM COLOR COAT:
- Agitar la llauna: Shake the aerosol can vigorously for at least one minute after the agitator ball begins to rattle. Continue to shake periodically during application.
- Spray de prova: Before applying to the actual surface, test spray on an inconspicuous area or a test panel to ensure color match and spray pattern.
- Temperatura d'aplicació: Apply at room temperature, ideally between 65°F (18°C) and 80°F (27°C).
- Distància de polvorització: Hold the can approximately 8-10 inches (20-25 cm) from the surface.
- Apply Thin Coats: Apply COLOR COAT in multiple thin, even coats. Avoid heavy coats, which can lead to runs or an uneven finish.
- Superposició: Superposeu cada passada aproximadament un 50% per assegurar una cobertura completa.
- Temps de repintat: Allow 5-10 minutes flash time between coats. Apply additional coats until desired color and coverage are achieved. Typically, 2-3 light coats are sufficient.
- Clear Nozzle: After each use, invert the can and spray for a few seconds to clear the nozzle, preventing clogs.
5. Drying and Curing
Drying times can vary based on temperature, humidity, and film thickness:
- Tack Free: Uns 10-15 minuts.
- Handleable: Uns 30 minuts.
- Curació completa: Allow 24 hours for the coating to fully cure before subjecting the surface to heavy use or cleaning.
6. Manteniment
Once cured, surfaces coated with SEM COLOR COAT can be cleaned with mild automotive interior cleaners. Avoid harsh chemicals or abrasive cleaning pads, as these may damage the finish. Regular cleaning will help maintain the appearance and longevity of the coating.
7. Solució De Problemes
| Problema | Causa possible | Solució |
|---|---|---|
| Mala adherència | Improper surface cleaning or preparation. | Ensure surface is thoroughly cleaned and degreased. Lightly scuff rigid plastics. |
| Uneven Finish / Runs | Applying coats too heavily or too close to the surface. | Apply multiple thin, even coats from the recommended distance. Allow adequate flash time between coats. |
| Clogging Nozzle | Paint drying in the nozzle. | Invert can and spray briefly after each use to clear the nozzle. |
| Desajust de color | Incorrect product selection or lighting conditions. | Always test spray on an inconspicuous area first. Ensure proper lighting for color evaluation. |
8. Especificacions
- Marca: SEM
- Número de model: 15363
- Color: Portola Red (as per product label)
- Tipus d'acabat: Setí
- Volum de l'article: 12 Fluid Ounces (340 g)
- Característica especial: Resistent a la decoloració
- Tipus de pintura: Esmalt
- Usos específics: Carpet, Vinyl, Plastic, Fabric
- Formulari de l'article: Aerosol
- Pes de l'article: 1.1 lliures
- Cobertura: Approximately 10 sq. ft. per can (varies with surface and application)
- Nivell de resistència a l'aigua: Resistent a l'aigua
9. Garantia i Suport
For specific warranty information or technical support regarding your SEM COLOR COAT product, please refer to the manufacturer's official weblloc web o contacteu directament amb el servei d'atenció al client. Conserveu el rebut de compra per a qualsevol reclamació de garantia.
