Heath Zenith SL-2735 Wired Doorbell Chime Instruction Manual

1. Producte acabatview

The Heath Zenith SL-2735 is a wired doorbell chime designed for hardwired installations. It features a sleek, modern white cover and provides two distinct chime sounds: a 2-note melody for the front entrance and a 1-note melody for the rear entrance. This allows for easy identification of which door a visitor is at.

Image: A white, sleek, modern design wired doorbell chime unit, typically mounted indoors.

2. Informació de seguretat

Llegiu atentament totes les instruccions abans de la instal·lació i l'ús. Si no seguiu aquestes instruccions, podeu patir descàrregues elèctriques, incendis o altres perills.

• Desconnecteu l'alimentació: Always turn off power at the circuit breaker or fuse box before installing, servicing, or removing the chime unit.
• Electricista qualificat: Si teniu dubtes sobre alguna part del procés d'instal·lació, consulteu un electricista qualificat.
• Voltage Requisits: This chime requires a 16-volt AC transformer (sold separately). Ensure the transformer meets the specified voltage.
• Advertència de la proposta 65: Aquest producte pot contenir productes químics coneguts per l'estat de Califòrnia per causar càncer i defectes de naixement o altres danys reproductius. Rentar-se les mans després de la manipulació.

3. Contingut del paquet

Verifiqueu que tots els components siguin presents abans de començar la instal·lació:

• Wired Doorbell Chime Unit (Model SL-2735)
• Hardware Kit (screws, anchors)

Nota: A 16-volt AC transformer and doorbell push buttons are sold separately and are required for operation.

4. Configuració i instal·lació

This doorbell chime is designed for hardwired installation. Follow these general steps for proper setup:

1. Apagueu l'alimentació: Locate the circuit breaker or fuse that controls the power to your existing doorbell system and turn it off. Verify power is off using a voltage provador.
2. Remove Old Chime: Carefully remove your old doorbell chime unit from the wall. Disconnect the existing wiring, noting which wires were connected to the front door, back door, and transformer terminals.
3. Mount New Chime: Position the Heath Zenith SL-2735 chime unit on the wall where you intend to install it. Mark the mounting screw locations. Drill pilot holes if necessary and secure the chime unit to the wall using the provided hardware.
4. Connexions de cable: Connect the wires from your doorbell push buttons and transformer to the corresponding terminals on the SL-2735 chime unit. Typically, there will be terminals for 'FRONT', 'REAR' (or 'BACK'), and 'TRANS' (or 'COMMON'). Ensure connections are secure.
5. Instal·lar la coberta: Carefully place the chime cover onto the unit.
6. Restaura l'alimentació: Torneu a connectar l'alimentació a l'interruptor o a la caixa de fusibles.
7. Prova de funcionament: Press your front and back doorbell buttons to ensure the chime sounds correctly for each entrance.

Nota important d'instal·lació: For the chime to produce the full "ding-dong" sound, the unit must be installed vertically. If installed horizontally, it may only produce a single "ding" sound, regardless of wiring configuration.

5. Instruccions de funcionament

The Heath Zenith SL-2735 doorbell chime operates automatically when a connected doorbell push button is pressed.

• Porta principal: When the front doorbell button is pressed, the chime will produce a distinctive 2-note melody.
• Rear Door: When the rear doorbell button is pressed, the chime will produce a single-note melody.

This differentiation allows you to easily identify which entrance a visitor is using.

6. Manteniment

The Heath Zenith SL-2735 doorbell chime requires minimal maintenance to ensure long-lasting performance.

• Neteja: Periodically wipe the chime cover with a soft, dry cloth to remove dust and dirt. Avoid using abrasive cleaners or solvents, as these can damage the finish.
• Comprovació de la connexió: If you experience intermittent operation, ensure all wiring connections are secure and free from corrosion. Always turn off power before inspecting electrical connections.
• Condicions ambientals: Ensure the chime unit is installed in a dry, indoor location, away from direct moisture or extreme temperatures.

7. Solució De Problemes

If your doorbell chime is not functioning as expected, refer to the following troubleshooting guide:

• Sense so de timbre:
  • Verify that power is supplied to the chime unit and transformer.
  • Check all wiring connections for looseness or corrosion.
  • Ensure the doorbell push buttons are functioning correctly.
  • Confirm the transformer is providing the correct 16-volt AC output.
• Only "Ding" Sound (No "Dong"):
  • The chime unit must be installed vertically for the full 2-note "ding-dong" melody to function correctly. Re-orient the unit if it is installed horizontally.
• Humming or Sporadic Chiming (with Smart Doorbells):
  • Some smart doorbells (e.g., Ring Pro 2) may require a higher-rated transformer, such as a 16V 30VA model, to prevent humming or inconsistent operation. Consult your smart doorbell's instructions for specific transformer requirements.
  • Ensure the chime settings within your smart doorbell app are correctly configured.
• Weak or Faint Chime Sound:
  • Check the transformer output voltage; a low voltage can result in a weak chime.
  • Ensure the chime's internal components (plungers, tone bars) are free from obstructions.

8. Especificacions

9. Informació de la garantia

This Heath Zenith SL-2735 Wired Doorbell Chime is covered by a 1 any de garantia from the manufacturer against defects in materials and workmanship. Please retain your proof of purchase for warranty claims. For specific warranty terms and conditions, refer to the documentation included with your product or contact Heath Zenith customer support.

10. Suport

For further assistance, technical support, or to inquire about replacement parts, please contact Heath Zenith customer service. Contact information can typically be found on the product packaging or the official Heath Zenith weblloc.

When contacting support, please have your product model number (SL-2735) and date of purchase available.