1. Producte acabatview
The Intermatic WG730-14D is a replacement motor designed for use in specific Intermatic timer series. It is engineered to restore the timing function of compatible devices, ensuring their continued operation.
Característiques principals:
- Compatibilitat: Specifically designed as a replacement motor for Intermatic timer series R8800, T1900, T1970, and T8800.
- Valoració elèctrica: Operates on 125 Volts Alternating Current (VAC).
- Freqüència: Designed for 60 Hz electrical systems.
- Conductors: Equipped with 14-inch electrical leads for connection.
Figura 1: Un primer pla view of the Intermatic WG730-14D 125V Time Clock Motor. The motor casing is metallic gray, displaying 'WG730', '125 V', '60 HZ', 'Intermatic', and 'MADE IN MEXICO'. Two white electrical leads with crimped terminals extend from one side. Small gears are visible on the other side of the motor.
2. Especificacions
| Fabricant | Intermatic |
| Número de part | WG730-14D |
| Pes de l'article | 3.2 unces |
| Dimensions del producte | 1.25 x 1.38 x 2.13 polzades |
| Voltage | 125 Volts |
| Freqüència | 60 Hz |
| Longitud del plom | 14 polzades |
| Piles necessàries | No |
3. Configuració i instal·lació
This motor is intended as a replacement part. Installation should only be performed by individuals familiar with electrical work and safety procedures. Always prioritize safety by disconnecting power before beginning any work.
Passos d'instal·lació:
- Desconnecteu l'alimentació: Locate the circuit breaker or fuse controlling the timer unit and turn off the power supply. Verify that power is off using a voltage provador.
- Temporitzador d'accés: Carefully open the timer enclosure or remove the timer mechanism from its housing to gain access to the existing motor.
- Treure el motor antic: Disconnect the electrical leads from the old motor. Note the orientation and connection points. Remove any screws or clips securing the old motor. Note: Retain any screws from the old motor, as new ones may not be included with the replacement motor.
- Instal·lar un motor nou: Position the new Intermatic WG730-14D motor in the same location as the old one. Secure it using the original screws or clips.
- Connecteu el cablejat: Connect the 14-inch electrical leads of the new motor to the appropriate terminals, ensuring a secure and correct connection.
- Torneu a muntar: Carefully reassemble the timer mechanism and close the timer enclosure.
- Restaura l'alimentació: Turn the power supply back on at the circuit breaker or fuse.
- Prova de funcionament: Verify that the timer is functioning correctly and keeping accurate time.
ADVERTIMENT: Risk of electric shock. Disconnect power before servicing. Improper installation can lead to injury or damage.
4. Instruccions de funcionament
The Intermatic WG730-14D motor is a component that drives the internal timing mechanism of compatible Intermatic timer units. Once correctly installed, the motor operates continuously to enable the timer's programmed functions.
Refer to the specific instruction manual for your Intermatic timer series (R8800, T1900, T1970, T8800) for detailed instructions on setting schedules, adjusting pins, and utilizing other timer features.
5. Manteniment
The WG730-14D motor is a sealed unit and does not require internal user maintenance. To ensure optimal performance and longevity of your timer system:
- Keep the timer enclosure clean and free from dust, dirt, and debris.
- Periodically inspect the electrical wiring and connections for any signs of wear, damage, or corrosion.
- Ensure the timer unit is protected from extreme temperatures and moisture, as specified by the timer's original manufacturer guidelines.
6. Solució De Problemes
If your timer unit is not functioning as expected after motor replacement, consider the following troubleshooting steps:
- Timer Not Running / Not Keeping Time:
- Verify that the power supply to the timer is active and stable.
- Ensure the motor's electrical leads are securely connected and free from damage.
- Confirm that the WG730-14D motor is compatible with your specific Intermatic timer series (R8800, T1900, T1970, T8800).
- If the timer operates manually (e.g., by flipping a switch) but fails to advance automatically, the motor is likely the cause and should be re-checked for proper installation or potential defect.
- Unusual Noises from Timer:
- A grinding or buzzing noise could indicate a mechanical issue with the motor or interference with the timer's gears. Disconnect power and inspect for obstructions. If the noise persists, the motor may need further inspection or replacement.
- Timer Not Activating/Deactivating Loads:
- While often related to the timer mechanism itself, ensure the motor is consistently driving the clock. If the clock is not advancing, the motor is not functioning correctly.
If troubleshooting steps do not resolve the issue, contact Intermatic customer support or a qualified electrician.
7. Informació de la garantia
For detailed warranty information regarding the Intermatic WG730-14D 125V Time Clock Motor, please refer to the manufacturer's official warranty description provided with the product packaging or visit the official Intermatic weblloc. Els termes i condicions de la garantia poden variar.
8. Suport i contacte
For further assistance, technical support, or inquiries regarding the Intermatic WG730-14D motor, please contact Intermatic directly:
- Visita l'Intermatic oficial weblloc web amb documentació del producte, preguntes freqüents i informació de contacte.
- Refer to the contact details provided in your product's original packaging.
