Miller Honeywell 3-Foot Cross-Arm Strap Anchorage Connector

1. Introducció

This instruction manual provides essential information for the safe and effective use, installation, and maintenance of the Miller Honeywell 3-Foot Cross-Arm Strap Anchorage Connector, Model 8183/3FTGN. This device is designed to serve as a secure anchorage point for personal fall arrest systems. Adherence to these instructions is critical for user safety and product longevity. Users must be trained and competent in the proper use of fall protection equipment.

2. Informació de seguretat

ADVERTIMENT: Failure to follow these instructions and warnings may result in serious injury or death. This product is part of a personal fall arrest system. Users must be trained by a competent person in the proper use of fall protection equipment.

• Always inspect the cross-arm strap and all connecting components before each use.
• Do not use if any signs of wear, damage, or degradation are present.
• Ensure the anchorage point can support a minimum of 5,000 lbs (22 kN) per worker attached.
• This product is designed for use by one person at a time unless otherwise specified by a competent person.
• Comply with all applicable ANSI, OSHA, and CSA regulations and standards.
• Consult a competent person or engineer if there is any doubt about the suitability of an anchorage point.

3. Característiques del producte

The Miller Honeywell 3-Foot Cross-Arm Strap Anchorage Connector offers the following key features:

• Secure Attachment Point: A 3-foot (0.9 m) cross-arm strap designed to wrap around I-beams and other structural elements.
• Fort Webbing: Constructed from 2-inch (50 mm) wide Polyester webbing with a minimum tensile strength of 5,000 lbs (22 kN).
• Alloy Steel D-Rings: Features a 2-inch (51 mm) D-ring that slips through a 3-inch (76 mm) D-ring to create a robust and secure attachment point. Both D-rings are rated to 5,000 lbs (22 kN) minimum tensile strength.
• Certificació: Meets all applicable ANSI, OSHA, and CSA requirements. All hardware complies with ASTM fifty-hour salt spray test requirements.

4. Configuració i instal·lació

To install the Miller Honeywell Cross-Arm Strap Anchorage Connector:

1. Identify a suitable anchorage point, such as an I-beam or other structural member, that can support the required load.
2. Wrap the 3-foot cross-arm strap around the chosen anchorage point.
3. Pass the smaller 2-inch D-ring through the larger 3-inch D-ring, creating a secure loop around the anchorage.
4. Pull the strap taut to ensure a snug fit around the anchorage point.
5. The larger D-ring, now hanging freely, serves as the attachment point for your lanyard or other connecting device.
6. Visually inspect the installed strap to confirm it is properly seated and free from twists or obstructions.

5. Instruccions de funcionament

Once the cross-arm strap is securely installed as an anchorage point:

• Connect your personal fall arrest system's lanyard or connecting device directly to the larger, free-hanging D-ring of the cross-arm strap.
• Ensure the connection is secure and properly engaged according to the manufacturer's instructions for your connecting device.
• Verify that there is sufficient clearance below the work area to prevent contact with a lower level in the event of a fall.
• Always maintain a clear understanding of your fall arrest system's components and their proper function.

6. Manteniment i Inspecció

Regular inspection and proper maintenance are crucial for the safety and performance of the cross-arm strap.

6.1. Inspecció prèvia a l'ús

Before each use, a competent person must perform a thorough visual inspection of the strap, including:

• Webbing: Check for cuts, fraying, excessive wear, burns, discoloration, or chemical damage.
• Costura: Examine all stitching for loose, broken, or pulled threads.
• Anells en D: Inspect for deformation, cracks, corrosion, sharp edges, or other damage. Ensure they pivot freely if designed to do so.
• Etiquetes: Verify that all labels are present and legible.

6.2. Inspecció periòdica

In addition to pre-use inspections, a competent person must perform a detailed inspection at least every six months, or more frequently depending on use and environmental conditions. Records of these inspections should be maintained.

6.3. Neteja i emmagatzematge

• Clean the strap with mild soap and water, then rinse thoroughly and allow to air dry completely away from direct sunlight or heat.
• Store the strap in a cool, dry, clean area, away from direct sunlight, extreme temperatures, corrosive chemicals, and other damaging elements.

7. Solució De Problemes

The Miller Honeywell Cross-Arm Strap is a passive anchorage connector. Troubleshooting primarily involves inspection and proper usage.

• Problema: Strap appears damaged (cuts, fraying, deformed D-rings).
  Solució: Immediately remove the strap from service. Do not attempt to repair. Dispose of or return to manufacturer for evaluation.
• Problema: Strap does not fit securely around the anchorage point.
  Solució: Ensure the anchorage point's dimensions are compatible with the strap. If the strap is too loose, it may not provide a secure connection. Select an appropriate anchorage or alternative equipment.
• Problema: Lanyard cannot connect to the D-ring.
  Solució: Verify the D-ring is free from obstruction and that the lanyard's connector is compatible and functioning correctly.

8. Especificacions

9. Garantia i Suport

For specific warranty information regarding the Miller Honeywell 3-Foot Cross-Arm Strap Anchorage Connector, please refer to the official Miller or Honeywell Safety Products website or contact their customer support directly. General inquiries and technical assistance can be obtained through the manufacturer's official channels.

Fabricant: Honeywell
Marca: Miller