1. Producte acabatview
The Oregon 60-009 Throttle Control Cable is a high-quality replacement part designed to restore proper throttle function to your equipment. This cable assembly is specifically engineered to replace McLane 1013B cables and is suitable for Edgers equipped with Briggs & Stratton engines, featuring a negative motion design.
Figura 1: The Oregon 60-009 Throttle Control Cable, showing the control lever and the cable assembly.
Característiques principals:
- Genuine Oregon replacement part.
- Complete throttle control cable assembly.
- Negative motion design.
- Compatible with Edgers equipped with Briggs & Stratton engines.
- Direct replacement for McLane 1013B.
2. Configuració i instal·lació
Proper installation is crucial for safe and effective operation. If you are unsure about any step, consult a qualified technician.
Eines necessàries:
- Wrench set (metric or SAE, depending on equipment)
- Joc de tornavisos (Phillips i de punta plana)
- Alicates
- Guants de seguretat i protecció ocular
Passos d'instal·lació:
- La seguretat primer: Ensure the equipment is turned off, the engine is cool, and the spark plug wire is disconnected to prevent accidental starting.
- Remove Old Cable: Locate the existing throttle control cable. Disconnect it from both the engine's throttle linkage and the control handle. Note how the old cable was routed.
- Instal·leu un cable nou: Route the new Oregon 60-009 cable in the same manner as the old one, ensuring it does not interfere with moving parts or hot surfaces.
- Connect to Engine: Attach the engine end of the cable to the throttle linkage. Ensure a secure connection that allows for full range of motion.
- Connect to Handle: Secure the control handle end of the cable. Ensure the lever operates smoothly and engages the throttle correctly.
- Prova de funcionament: Reconnect the spark plug wire. Start the engine (if applicable) and test the throttle control. Ensure the engine idles correctly and reaches full throttle when the lever is engaged. Adjust tension if necessary.
3. Instruccions de funcionament
The throttle control cable allows you to adjust the engine speed of your equipment. Familiarize yourself with its operation before use.
Palanca de control de l'accelerador:
- Posició de repòs: When the lever is in the 'Idle' or 'Slow' position, the engine will run at its lowest RPM, conserving fuel and reducing noise.
- Posició de màxima acceleració: Moving the lever to the 'Fast' or 'Full Throttle' position will increase the engine's RPM to its maximum operating speed, providing full power for tasks like edging.
- Asfixia (si escau): Some control levers may integrate a choke function for cold starts. Refer to your equipment's specific manual for choke operation.
Always operate the throttle smoothly and avoid sudden, jerky movements. Ensure the cable moves freely without binding.
4. Manteniment
Regular maintenance of your throttle control cable will ensure its longevity and reliable performance.
- Lubricació: Periodically apply a light lubricant (e.g., silicone spray or light oil) to the cable ends and any exposed moving parts of the control lever. This helps prevent corrosion and ensures smooth operation.
- Inspecció: Regularly inspect the cable for signs of wear, fraying, kinks, or damage to the outer casing. Check the connections at both ends for looseness or corrosion.
- Neteja: Keep the control lever and cable free from dirt, debris, and grass clippings. A clean cable is less likely to bind.
- Ajust: If the throttle response feels sluggish or the engine does not reach full RPM, the cable tension may need adjustment. Refer to your equipment's service manual for specific adjustment procedures.
5. Solució De Problemes
Here are some common issues and their potential solutions related to the throttle control cable.
| Problema | Causa possible | Solució |
|---|---|---|
| Throttle lever is stiff or hard to move. | Lack of lubrication, kinked cable, debris in casing. | Lubricate cable, check for kinks, clean cable path. |
| Engine does not reach full throttle. | Cable stretched, improper adjustment, linkage obstruction. | Adjust cable tension, check linkage for obstructions, replace cable if stretched. |
| Engine does not idle properly. | Cable too tight, linkage obstruction. | Adjust cable tension, ensure linkage returns freely to idle position. |
| Cable appears frayed or damaged. | Wear and tear, external damage. | Replace the cable immediately to prevent failure. |
6. Especificacions
| Atribut | Valor |
|---|---|
| Número de part | 60-009 |
| Dimensions del producte | 37.59 x 19.18 x 4.83 cm |
| Assembled Item Height | 24 polzades |
| Assembled Item Length | 4 polzades |
| Assembled Item Width | 4 polzades |
| Assembled Item Weight | 1.3 lliures |
| Tipus de font d'alimentació | Funciona amb gas |
| Fabricant | Oregon |
| ASIN | B0018U2DT2 |
| Data de primera disponibilitat | 14 d'agost de 2012 |
7. Garantia i Suport
Oregon products are manufactured to high standards and are backed by a commitment to quality. For specific warranty information or technical support, please refer to the official Oregon weblloc web o contacteu directament amb el seu servei d'atenció al client. Conserveu el rebut de compra com a comprovant de compra.
Per a més ajuda, podeu visitar el Oregon Brand Store on Amazon.
