1. Introducció
The Blue Wave NA324 Widemouth Skimmer/Return is designed to efficiently collect debris from your pool, ensuring cleaner water and optimal filtration. Its wide mouth design enhances debris collection, providing maximum performance and durability. This manual provides essential information for the proper setup, operation, and maintenance of your skimmer.
2. Producte acabatview

Figura 2.1: Frontal view of the skimmer, showing the wide opening and screw points for mounting.

Figura 2.2: Angle view of the skimmer, highlighting the internal flap and deep body design.

Figura 2.3: lateral view of the skimmer, showing the overall dimensions and pipe connection point.
3. Configuració i instal·lació
3.1 Components inclosos
- Widemouth Skimmer Body (two-piece material)
- Locking Basket
- 1-1/2-inch FPT (Female Pipe Thread) Adapter
- 1-1/2-inch Hose Adapter
- Mounting Screws (typically included, verify with packaging)
- Gaskets/Seals (typically included, verify with packaging)
3.2 Passos d'instal·lació
Proper installation is crucial for the skimmer's performance. If you are unsure about any step, consult a qualified pool professional.
- Prepare the Pool Wall: Ensure the area on the pool wall where the skimmer will be installed is clean and free of obstructions. If replacing an existing skimmer, remove the old unit and clean the opening thoroughly.
- Position the Skimmer: Place the skimmer body against the pool wall, aligning it with the pre-cut opening. Ensure the skimmer is level.
- Instal·lar juntes: Apply appropriate gaskets (not explicitly listed but essential for sealing) around the skimmer opening on both the inside and outside of the pool wall to prevent leaks.
- Secure the Skimmer: Using the provided screws, attach the skimmer faceplate to the skimmer body, sandwiching the pool liner/wall and gaskets. Tighten screws evenly to create a watertight seal. Do not overtighten.
- Connecteu la fontaneria: Attach the 1-1/2-inch FPT adapter or 1-1/2-inch hose adapter to the bottom port of the skimmer, depending on your pool's plumbing system. Ensure all connections are sealed properly using thread sealant or Teflon tape.
- Install Skimmer Basket: Place the locking basket inside the skimmer body. This basket will collect large debris before it reaches your pump.
- Fill Pool to Operating Level: Once installation is complete and all connections are secure, fill your pool to the recommended operating water level, which should be about halfway up the skimmer opening.
4. Funcionament
The Blue Wave NA324 Widemouth Skimmer/Return operates by drawing water from the pool surface, where most floating debris accumulates. The wide mouth design maximizes the area from which debris can be collected, improving the efficiency of your pool's filtration system.
- Nivell d'aigua: Maintain the pool water level at approximately the middle of the skimmer opening for optimal skimming action. If the water level is too low, the skimmer may draw air, affecting pump performance. If too high, skimming efficiency will be reduced.
- Skimmer Weir: The skimmer features a weir (flap) that helps regulate water flow and prevents debris from floating back into the pool when the pump is off. Ensure the weir moves freely.
- Basket Function: The internal locking basket traps leaves, insects, and other large debris, preventing them from clogging your pump or filter.
5. Manteniment
Regular maintenance of your skimmer is essential for efficient pool operation and longevity of your equipment.
- Empty Skimmer Basket: Check and empty the skimmer basket daily or as needed, especially after heavy winds or storms. A full basket restricts water flow and reduces skimming efficiency.
- Turn off the pool pump to prevent suction.
- Remove the skimmer lid.
- Lift out the locking basket.
- Empty debris into a trash receptacle.
- Rinse the basket with a hose to remove any remaining small particles.
- Return the clean basket to the skimmer and replace the lid securely.
- Turn the pool pump back on.
- Inspect Skimmer Weir: Periodically check the skimmer weir (flap) to ensure it moves freely and is not obstructed by debris.
- Comproveu si hi ha esquerdes o danys: Inspect the skimmer body and faceplate for any signs of cracks or damage, which could lead to leaks. Address any issues promptly.
- Clean Skimmer Interior: Occasionally, you may need to clean the interior of the skimmer body to remove algae or stubborn debris buildup.
6. Solució De Problemes
Consulteu la taula següent per veure els problemes habituals i les seves possibles solucions.
| Problema | Causa possible | Solució |
|---|---|---|
| Poor Skimming Action |
|
|
| Water Leaking Around Skimmer |
|
|
| Skimmer Drawing Air |
|
|
7. Especificacions tècniques
| Característica | Especificació |
|---|---|
| Marca | Onada Blava |
| Número de model | NA324 |
| Material | Plàstic |
| Color | Blanc |
| Estil | Modern |
| Dimensions del producte | 12 x 6 x 16 polzades |
| Pes de l'article | 1 lliures (16 unces) |
| Fil de canonada | 1-1/2-inch FPT |
| Adaptador de mànega | 1-1/2 polzades |
| Fabricant | Productes Blue Wave |
| UPC | 672875690053 |





