SEM 70011 Integral Nut Square Static Mixer Kit User Manual

1. Introducció

This manual provides essential instructions for the proper use and maintenance of the SEM 70011 Integral Nut Square Static Mixer Kit. Please read this manual thoroughly before use to ensure safe and effective operation.

2. Producte acabatview

The SEM 70011 Integral Nut Square Static Mixer is designed for efficient mixing of two-component (2K) cartridge products. Its integral nut design allows for direct attachment to compatible 7oz cartridges, ensuring a secure connection and consistent mixing performance.

Característiques principals:

• Integral Nut design for secure cartridge attachment.
• Square static mixing elements for thorough and consistent material blending.
• Suitable for use with most 2K 7oz cartridge products.

Figure 1: SEM 70011 Integral Nut Square Static Mixer. This image displays the SEM 70011 Integral Nut Square Static Mixer. It features a translucent plastic housing with a threaded integral nut at one end for attachment to a cartridge. Inside, a series of red, interlocking square elements are visible, designed to thoroughly mix two-component materials as they pass through.

3. Configuració i instal·lació

1. Prepare Cartridge: Ensure the 2K cartridge product is ready for use. Remove the cap from the cartridge.
2. Purge Cartridge: Before attaching the mixer, dispense a small amount of material from the cartridge to ensure both components are flowing evenly and to purge any air.
3. Attach Mixer: Align the integral nut of the static mixer with the outlet of the 2K cartridge. Thread the mixer onto the cartridge outlet until it is securely hand-tight. Do not overtighten.
4. Initial Dispense: Dispense a small amount of material through the mixer onto a scrap surface to ensure proper mixing has begun and to clear any unmixed material from the initial section of the mixer.

4. Instruccions de funcionament

Once the static mixer is securely attached and purged, the system is ready for application.

• Aplicació: Apply the mixed material directly to the desired surface or area. Maintain a steady pressure on the cartridge dispenser for consistent flow.
• Caudal: The flow rate will depend on the viscosity of the material and the pressure applied to the cartridge. Adjust as needed for your specific application.
• Ús sol: Static mixers are generally designed for single use. Once material has cured within the mixer, it cannot be reused.

5. Manteniment i emmagatzematge

• Neteja: Static mixers are disposable. Do not attempt to clean or reuse a mixer once material has been dispensed through it and cured.
• Emmagatzematge: Store unused static mixers in their original packaging in a cool, dry place, away from direct sunlight and extreme temperatures.
• Eliminació: Dispose of used mixers according to local regulations for chemical waste, especially if hazardous materials were used.

6. Solució De Problemes

• Poor Mixing:
  • Ensure the mixer is fully and securely attached to the cartridge.
  • Verify that both components of the 2K product are flowing evenly from the cartridge before attaching the mixer.
  • Dispense a small amount of material through the mixer to ensure proper initial mixing.
• Mixer Detaches:
  • Ensure the integral nut is securely hand-tightened onto the cartridge.
  • Check for compatibility between the mixer and the cartridge outlet.
• No hi ha flux de:
  • Check if the cartridge nozzle is clogged or if the material has cured inside the cartridge or mixer.
  • Ensure the cartridge dispenser is functioning correctly.

7. Especificacions

8. Garantia i Suport

For specific warranty information regarding the SEM 70011 Integral Nut Square Static Mixer, please refer to the documentation provided with your 2K cartridge product or contact SEM directly. As a consumable item, static mixers typically do not carry an extended warranty.

For technical support or inquiries, please visit the official SEM weblloc o poseu-vos en contacte amb el seu departament d'atenció al client.