1. Producte acabatview
The SEM MULTIMAX 61023 Semi-Gloss Black is a multi-purpose aerosol enamel designed for both exterior and interior applications. It provides a durable, fast-drying finish with excellent adhesion and outstanding coverage on various surfaces.
Característiques principals:
- Outstanding coverage
- Excellent filling properties
- Durable, fast-drying finish
- Great adhesion
- Acabat professional
Image 1: SEM MULTIMAX 61023 Semi-Gloss Black aerosol can, showing the product label and branding.
2. Informació de seguretat
ADVERTIMENT: This product is an extremely flammable aerosol. Read all cautions on the back panel of the can before use. Failure to follow safety instructions may result in serious injury or property damage.
- Inflamabilitat: Keep away from heat, sparks, open flames, and hot surfaces. Do not spray near any ignition source.
- Contenidor pressuritzat: Do not pierce or burn, even after use. Do not expose to temperatures exceeding 120°F (49°C) as the container may burst.
- Ventilació: Use only in a well-ventilated area. Inhalation of vapors may be harmful. If ventilation is poor, wear appropriate respiratory protection.
- Protecció ocular: Wear safety glasses with side shields to prevent eye contact. Causes serious eye irritation.
- Protecció de la pell: Wear protective gloves to avoid skin contact. Prolonged or repeated skin contact may cause irritation.
- Ingestió: Harmful or fatal if swallowed. Do not ingest. If swallowed, seek immediate medical attention.
- Mantenir fora de l'abast dels nens: Store in a secure location inaccessible to children and pets.
3. Preparació
3.1 Preparació de la superfície
Proper surface preparation is crucial for optimal adhesion and finish quality.
- Neteja: Ensure the surface is clean, dry, and free from dirt, grease, oil, wax, rust, and loose paint. Use a suitable cleaner or degreaser if necessary.
- Sorra: Lightly sand glossy surfaces or bare metal/plastic with fine-grit sandpaper (e.g., 320-400 grit) to create a profile per a una millor adherència. Netegeu la pols de poliment.
- Màscara: Mask off any areas not intended for painting using painter's tape and masking paper or plastic.
3.2 Can Preparation
- Shake the can vigorously for at least one minute after the mixing ball begins to rattle. Continue to shake periodically during application.
- Test spray on an inconspicuous area or scrap material to check color and spray pattern.
4. Aplicació (operativa)
Apply in a well-ventilated area, ideally between 65°F and 75°F (18°C and 24°C) with humidity below 60%.
- Hold the can upright approximately 8-10 inches (20-25 cm) from the surface.
- Apply paint in light, even coats using a steady, sweeping motion. Avoid heavy coats to prevent runs and drips.
- Overlap each pass by about one-third to ensure uniform coverage.
- Allow 5-10 minutes flash time between coats. Apply multiple thin coats rather than one thick coat for best results.
- For best results, apply 2-3 light coats.
5. Drying and Curing
Drying times may vary depending on temperature, humidity, and film thickness.
- To Touch: Uns 15-30 minuts.
- To Handle: Aproximadament 1-2 hores.
- Curació completa: Allow 24-48 hours for the paint to fully cure and achieve maximum hardness and durability.
6. Cleanup and Storage
6.1 Neteja
- After each use, invert the can and spray for 2-3 seconds until only clear propellant comes out. This clears the nozzle and prevents clogging.
- Wipe any excess paint from the nozzle with a rag.
6.2 Emmagatzematge
- Store the can in a cool, dry, well-ventilated area, away from direct sunlight, heat sources, and open flames.
- Do not store at temperatures above 120°F (49°C).
- Ensure the cap is securely placed on the can to prevent accidental discharge.
7. Solució De Problemes
| Problema | Causa possible | Solució |
|---|---|---|
| Broquet obstruït | Paint dried in nozzle; can not inverted after use. | Remove nozzle and soak in mineral spirits or paint thinner. If severely clogged, replace nozzle. Always invert and clear nozzle after use. |
| Uneven Spray/Runs | Can held too close; too much paint applied in one coat; insufficient shaking. | Hold can 8-10 inches from surface. Apply multiple light coats. Shake can thoroughly before and during use. |
| Mala adherència | Surface not properly cleaned or prepared; incompatible surface. | Ensure surface is clean, dry, and properly sanded. Use on recommended surfaces only (metal, wood, fiberglass, rigid plastic). |
| Assecat lent | High humidity; low temperature; heavy coats. | Ensure proper ventilation and temperature. Apply thinner coats. Allow adequate drying time between coats. |
8. Especificacions
| Especificació | Detall |
|---|---|
| Marca | SEM |
| Nom del model | 61023 |
| Color | Negre semi brillant |
| Tipus d'acabat | Semibrillant |
| Mida | 16 oz Aerosol Can |
| Volum de l'article | 16 unces líquides |
| Tipus de pintura | Esmalt |
| Usos específics per al producte | Interior, Exterior |
| Recomanació de superfície | Metal, Wood, Fiberglass, Rigid Plastic |
| Formulari d'article | Aerosol |
| Pes de l'article | 1 lliures |
| UPC | 646786610233 |
9. Garantia i Suport
Specific warranty information for SEM MULTIMAX 61023 is not provided in this manual. For detailed warranty terms or technical support, please contact SEM Products Inc. directly through their official weblloc o canals d'atenció al client.
Always refer to the product label for the most current safety and usage instructions.
