Introducció
The Rheem SP11698 Electric Thermostat is designed for use in residential electric water heaters. This unit provides reliable temperature control and features a high-limit safety mechanism to prevent overheating. Proper installation and operation are crucial for safety and optimal performance.
Informació important de seguretat
Si us plau, llegiu i enteneu totes les instruccions abans d'instal·lar o fer funcionar aquest termòstat. Si no seguiu aquestes instruccions, podeu patir danys materials, lesions personals o la mort.
- Desconnecteu l'alimentació: Always turn off the main power supply to the water heater at the circuit breaker or fuse box before performing any installation, maintenance, or troubleshooting.
- Personal qualificat: Installation and servicing of this thermostat should only be performed by a qualified electrician or plumber.
- Temperatura de l'aigua: Be aware that water temperatures above 125°F (52°C) can cause severe burns or scalding. Exercise caution when setting the thermostat.
- Cablejat adequat: Assegureu-vos que totes les connexions de cablejat siguin segures i que compleixin els codis elèctrics locals.
- Posada a terra: The water heater and all electrical components must be properly grounded.
Instal·lació
Abans de començar
- Ensure the water heater is completely drained and depressurized if replacing elements or performing extensive work.
- Turn off all power to the water heater at the main electrical panel. Verify power is off using a voltage provador.
- Remove the access panels and insulation covering the existing thermostat.
- Take a clear photograph of the existing wiring connections before disconnecting any wires. This will serve as a reference.
Instruccions de cablejat
The Rheem SP11698 thermostat is designed for straightforward replacement. Carefully disconnect the wires from the old thermostat, noting their positions. Connect the wires to the new Rheem SP11698 thermostat in the exact same configuration. Refer to the wiring diagram below for contact configuration details.

This diagram illustrates the internal contact configuration for both the High Limit and Thermostat sections. 'C' denotes Common, 'NC' denotes Normally Closed, and 'NO' denotes Normally Open. Contacts open when the temperature is above the setpoint. The manual reset feature is also indicated for the High Limit.
After wiring, ensure the thermostat is securely mounted against the water heater tank. Replace insulation and access panels.
Producte acabatview Vídeo
Aquest vídeo ofereix una visió generalview of the Rheem SP11698 Electric Thermostat, highlighting its key features and demonstrating its physical characteristics. While not a step-by-step installation guide, it offers helpful context for understanding the product.
Funcionament
Once installed and power is restored, the thermostat will begin regulating the water temperature. The Rheem SP11698 features a temperature control dial for setting the desired water temperature and a high-limit safety reset.
- Configuració de la temperatura: Adjust the temperature dial to your preferred setting. It is recommended to set the temperature between 120°F (49°C) and 125°F (52°C) to balance comfort and energy efficiency while minimizing scalding risk.
- High-Limit Reset: If the water temperature exceeds a safe limit, the high-limit switch will trip, cutting power to the heating elements. To reset, press the red manual reset button located on the thermostat. If the high-limit trips repeatedly, consult a qualified technician to diagnose the underlying issue.
Manteniment
Regular maintenance helps ensure the longevity and efficient operation of your water heater and thermostat.
- Inspecció anual: Have a qualified technician inspect your water heater and its components, including the thermostat, annually.
- Comproveu les connexions: Periodically, with power disconnected, check all electrical connections to the thermostat and heating elements to ensure they are tight and free from corrosion.
- Mantenir la zona neta: Ensure the area around the water heater is clear of obstructions and flammable materials.
Resolució de problemes
If you experience issues with your water heater, the thermostat may be a factor. Always disconnect power before inspecting components.
| Problema | Causa possible | Solució |
|---|---|---|
| Sense aigua calenta | High-limit switch tripped | Press the red manual reset button. If it trips again, investigate further. |
| Sense aigua calenta | Falla del termòstat | Test thermostat for continuity. Replace if faulty. |
| Aigua massa calenta/freda | Configuració de temperatura incorrecta | Ajusteu el dial de temperatura a la configuració desitjada. |
| Aigua massa calenta/freda | Termòstat defectuós | Test thermostat for proper operation. Replace if temperature regulation is inconsistent. |
For persistent issues or if you are unsure about any troubleshooting steps, contact a qualified service technician.
Especificacions
| Característica | Detall |
|---|---|
| Marca | Rheem |
| Nom del model | Rheem SP11698 Electric Thermostat |
| Número de part | SP11698 |
| Dimensions del producte | 2 "P x 3.6" W x 2" H |
| Tipus de controlador | Toca |
| Característica especial | High-Limit Protection |
| Color | Negre |
| Usos específics per al producte | Escalfadors d'aigua |
| Tipus de control de temperatura | Digital |
| Font d'alimentació | Elèctric amb cable |
| Voltage | 220 Volts |
| Pes de l'article | 5.6 unces |
| UPC | 020352381794 |
Garantia i Suport
For specific warranty information regarding your Rheem SP11698 Electric Thermostat, please refer to the documentation included with your purchase or visit the official Rheem website. If you require technical assistance, replacement parts, or have questions not covered in this manual, please contact Rheem customer support directly.
Rheem Customer Support: Si us plau, visiteu www.rheem.com/support per obtenir informació de contacte i recursos addicionals.





