1. Producte acabatview
The Sicce Ultrazero Flat Sucking Pump is designed for efficient removal of water from various areas, including flooded cellars, garages, and other spaces where minimal residual water is desired. This submersible pump is capable of reducing water levels down to 2-3 mm.
Característiques principals:
- Capable of pumping water down to 2 mm residual level.
- Fully submersible design.
- Handles dirt particles up to 3 mm in size.
- Equipped with a 10-meter power cable.
- Features a practical carry handle for easy transport.
Figura 1: Mésview of the Sicce Ultrazero Flat Sucking Pump.
2. Informació de seguretat
Read all safety warnings and instructions before operating the pump. Failure to follow these instructions may result in electric shock, fire, or serious injury.
- Desconnecteu sempre la bomba de la xarxa elèctrica abans de manipular-la, netejar-la o realitzar qualsevol manteniment.
- Assegureu-vos que la font d'alimentació voltage matches the pump's specifications (230 V/50 Hz).
- Do not operate the pump with a damaged power cord or plug. If damaged, it must be replaced by the manufacturer, service agent, or similarly qualified persons to avoid a hazard.
- Do not use the pump to handle flammable or explosive liquids.
- Mantingueu els nens i les persones no autoritzades allunyats de la zona d'operació.
- Assegureu-vos que la bomba estigui completament submergida durant el funcionament per evitar el sobreescalfament.
- Avoid running the pump dry for extended periods.
- This pump is designed for water only. Do not use it for other liquids without consulting the manufacturer.
3. Configuració i instal·lació
Follow these steps to properly set up your Ultrazero pump:
- Desempaquetar la bomba: Traieu amb cura la bomba i tots els accessoris de l'embalatge. Inspeccioneu-ho per veure si hi ha algun dany.
- Connect the Discharge Hose:
The pump features a 26.44 mm (3/4") AG pressure connection. Attach a suitable discharge hose (e.g., 20 mm (3/4") hose connection) to this outlet. Ensure the connection is secure to prevent leaks.
Figure 2: Close-up of the pump's discharge outlet and integrated carry handle.
- Posició de la bomba: Place the pump directly on the surface from which water needs to be removed. Ensure the pump is stable and upright. The flat base allows for efficient water removal down to minimal levels.
- Route the Discharge Hose: Direct the discharge hose to a suitable drainage area, ensuring the water will not flow back into the area being drained.
- Connexió d'alimentació: Plug the 10-meter power cable into a grounded 230 V/50 Hz electrical outlet. Ensure the outlet is protected by a Ground Fault Circuit Interrupter (GFCI) for added safety, especially in wet environments.
Figure 3: The flat base of the pump designed for low residual water levels.
4. Instruccions de funcionament
The Ultrazero pump is designed for simple operation:
- Submergir la bomba: Ensure the pump is fully submerged in the water you wish to remove. The pump requires water to cool its motor and operate correctly.
- Començar el bombeig: Once submerged and connected to power, the pump will begin operating automatically. It does not feature a float switch, so manual monitoring is required for optimal use.
- Monitor del nivell d'aigua: The pump will continue to operate until the water level reaches its minimum suction capability of 2-3 mm.
- Aturar el bombament: To stop the pump, disconnect it from the power supply. It is recommended to disconnect the pump once the desired water level is reached or if the pump starts to run dry.
Figure 4: The Ultrazero pump effectively draining water from a small pool.
Figure 5: The pump in action on a flooded floor, demonstrating its low-level suction capability.
Figure 6: Illustration of the pump's ability to reduce water levels to approximately 2 mm.
5. Manteniment
Un manteniment regular garanteix la longevitat i el rendiment òptim de la bomba.
- Neteja: After each use, especially when pumping dirty water, rinse the pump thoroughly with clean water. This helps prevent sediment buildup.
- Inspeccioneu si hi ha deixalles: Periodically check the pump's intake area for any debris (e.g., leaves, small stones) that might obstruct water flow. Remove any blockages carefully after disconnecting power.
- Inspecció del cable: Regularly inspect the power cable for cuts, abrasions, or other damage. Do not use the pump if the cable is damaged.
- Emmagatzematge: When not in use, store the pump in a clean, dry place, protected from frost.
Figure 7: The pump can also be used for transferring water for tasks like garden watering from a rain barrel.
6. Solució De Problemes
If you encounter issues with your Ultrazero pump, refer to the following common problems and solutions:
| Problema | Causa possible | Solució |
|---|---|---|
| La bomba no arrenca. | Sense font d'alimentació. Cable d'alimentació danyat. Protecció de sobrecàrrega del motor activada. | Comproveu la connexió i la presa de corrent. Inspect cable for damage; replace if necessary (by qualified personnel). Disconnect power, allow motor to cool, then reconnect. |
| La bomba funciona però no surt aigua. | Intake blocked. Mànega de descàrrega doblegada o bloquejada. Airlock in pump. | Disconnect power, clear intake. Check and clear discharge hose. Briefly lift and lower the pump while submerged to release trapped air. |
| Reduced pumping performance. | Partial blockage. Impeller worn. | Disconnect power, clean pump intake and impeller area. Poseu-vos en contacte amb l'atenció al client per obtenir servei. |
| La bomba s'atura inesperadament. | Overheating due to low water level or blockage. Falla elèctrica. | Disconnect power, check water level and clear blockages. Allow to cool. Si el problema persisteix, contacteu amb l'atenció al client. |
If the problem persists after attempting these solutions, please contact Sicce customer support.
7. Especificacions tècniques
Detailed specifications for the Sicce Ultrazero Flat Sucking Pump, Model 925607:
| Especificació | Valor |
|---|---|
| Marca | Sicce |
| Número de model | 925607 |
| Max. Delivery Rate (Flow Rate) | 3000 l/h |
| Màx. Alçada de lliurament | 3.1 m |
| Power Consumption (P1) | 80 W |
| Vol. Operatiutage | 220-240 V / 50 Hz |
| Conductor Length (Power Cable) | 10 m (three-core, indoor and outdoor use) |
| Connexió de pressió | 26.44 mm (3/4") AG |
| Diàmetre de connexió de la mànega | 20 mm (3/4") |
| Max. Solids Size | 3 mm |
| Nivell d'aigua residual | Down to 2-3 mm |
| Dimensions del producte (aprox.) | 140 mm (Diameter) x 160 mm (Height) / 5.5" x 6.3" |
| Pes de l'article | 2.6 kg (5.72 lliures) |
| Interruptor de flotació | No |
| Protecció de sobrecàrrega | No (Internal thermal protection may exist, but no external reset) |
| Origen | Fabricat a Itàlia |
Figure 8: Technical drawing illustrating the pump's dimensions and 3/4" GAS connection.
8. Garantia i Suport
For warranty information or technical support regarding your Sicce Ultrazero Flat Sucking Pump, please contact Sicce customer service. Keep your purchase receipt and model number (925607) handy when contacting support.
Fabricant: Ebara
Marca: Sicce
For further assistance, visit the official Sicce weblloc web o poseu-vos en contacte amb el vostre distribuïdor local.
