WAC Lighting LHT-007L-WT Low Voltage Track Head

Introducció

This manual provides detailed instructions for the safe installation, operation, and maintenance of your WAC Lighting LHT-007L-WT Low Voltage Track Head. This product is designed for use with Lightolier Series track systems and accommodates a 75W MR16 halogen bulb. Please read all instructions carefully before proceeding with installation or use.

Informació de seguretat

• Always turn off power at the circuit breaker before installing, servicing, or changing bulbs.
• Aquest producte s'ha d'instal·lar d'acord amb el codi d'instal·lació aplicable per una persona familiaritzada amb la construcció i el funcionament del producte i els perills que comporta.
• Use only with Lightolier Series track systems.
• No supereu la potència màximatage of 75W for the MR16 halogen bulb.
• Ensure the track head is securely fastened to the track before restoring power.
• Avoid touching the bulb directly with bare hands, as oils can reduce bulb life. Use a clean cloth or glove.

Contingut del paquet

Verifiqueu que tots els components siguin presents:

• 1 x WAC Lighting LHT-007L-WT Low Voltage Track Head (White)
• Manual d'instruccions (aquest document)

Note: MR16 halogen bulb is typically sold separately.

Configuració i instal·lació

Follow these steps to install your track head:

1. Prepare the Track: Ensure the track system is properly installed and secured to the ceiling or wall. Verify that the power to the track circuit is OFF at the breaker.
2. Insereix la bombeta: Carefully insert the MR16 halogen bulb into the track head. Do not touch the bulb glass with bare hands.
3. Attach to Track: Align the track head's adapter with the track slot. Push the adapter firmly into the track and rotate the locking tab (if present) to secure it in place. Ensure the head is fully seated and cannot be easily pulled out.
4. Ajustar la direcció: Once secured, the track head can be swiveled and tilted to direct light as desired.
5. Restaura l'alimentació: After installation is complete and verified, restore power at the circuit breaker.

Figure 1: WAC Lighting LHT-007L-WT Low Voltage Track Head. This image shows the complete track head assembly, highlighting its white finish and the MR16 bulb housing.

Figure 2: Dimensional drawing of the track head. This diagram provides precise measurements for height, width, and depth, useful for planning installation and clearances.

Instruccions de funcionament

Once installed and powered, the track head operates as follows:

• Encès/apagat: The track head is controlled by the wall switch connected to the track circuit.
• Ajust direccional: The track head can be manually swiveled 350 degrees horizontally and tilted 90 degrees vertically to aim the light beam.
• Dimecres: This track head is dimmable when used with a compatible dimmer switch on the circuit and a dimmable MR16 halogen bulb.

Figura 3: Example application of WAC Lighting track heads in a retail setting. This image demonstrates how multiple track heads can be used on a single track to illuminate various display areas.

Manteniment

Regular maintenance ensures optimal performance and longevity of your track head:

• Neteja: Disconnect power before cleaning. Wipe the exterior of the track head with a soft, dry cloth. Do not use abrasive cleaners or solvents.
• Substitució de bombetes: Turn off power at the circuit breaker. Allow the bulb to cool completely. Carefully remove the old MR16 bulb and insert a new one, ensuring it is rated for 75W or less. Avoid touching the new bulb with bare hands. Restore power after replacement.

Resolució de problemes

Si teniu problemes, consulteu els següents problemes i solucions habituals:

• La llum no s'encén:
  • Comproveu si l'interruptor està en ON.
  • Ensure the wall switch is ON.
  • Verify the bulb is correctly seated and not burnt out. Replace if necessary.
  • Confirm the track head is securely connected to the track.
• Parpelleig de llum:
  • Check bulb connection; ensure it is fully inserted.
  • If using a dimmer, ensure it is compatible with halogen low voltage lighting and the bulb.
  • Ensure the track head is making proper contact with the track.
• Track head is loose on track:
  • Turn off power. Re-seat the track head and ensure the locking tab is fully engaged.

If problems persist, contact a qualified electrician or WAC Lighting customer support.

Especificacions

Garantia i Suport

WAC Lighting products are manufactured to the highest standards and are backed by a manufacturer's warranty. For specific warranty details, please refer to the warranty card included with your purchase or visit the official WAC Lighting website. For technical support, replacement parts, or further assistance, please contact WAC Lighting customer service directly.

WAC Lighting Contact Information:
Please refer to the official WAC Lighting weblloc web o l'embalatge del producte per obtenir les dades de contacte més actualitzades.