Introducció
This manual provides detailed instructions for the installation, operation, and maintenance of your Wolo Apollo 8 GEN 3 LED Emergency Warning Light, Model 3095PPM-C. Please read this manual thoroughly before use to ensure proper function and safety.
The Wolo Apollo 8 GEN 3 LED Emergency Warning Light, Model 3095PPM-C, features a clear lens and a robust design for various mounting applications.
Instruccions importants de seguretat
- Assegureu-vos que totes les connexions elèctriques estiguin ben fixades i degudament aïllades per evitar curtcircuits.
- Verify the vehicle's electrical system voltage matches the light's operating voltage (12-60V DC).
- Disconnect the vehicle's battery before beginning installation to prevent electrical shock.
- Mount the light securely to prevent detachment during vehicle operation.
- Adhere to all local and national regulations regarding the use of emergency warning lights.
Contingut del paquet
- Wolo Apollo 8 GEN 3 LED Emergency Warning Light (Model 3095PPM-C)
- Maquinari de muntatge (cargols, femelles, volanderes)
- Terminals de filferro
- In-line Fuse Holder
- Junta de goma
- Manual d'instruccions (aquest document)
Configuració i instal·lació
The Apollo 8 warning light offers two primary mounting options: permanent surface mount or pipe mount.
Permanent Surface Mount
- Choose a flat, stable surface on your vehicle for mounting. Ensure the location provides clear 360° visibility.
- Use the provided rubber gasket as a template to mark the drilling locations for the mounting screws.
- Perforeu forats pilot als llocs marcats.
- Secure the light base to the surface using the provided mounting hardware (screws, washers, nuts). Ensure a tight fit to prevent vibration.
- Route the power wires to the vehicle's electrical system. Connect the positive wire (typically red) to a switched 12-60V DC power source via the in-line fuse holder. Connect the negative wire (typically black) to a suitable ground point on the vehicle chassis.
- Ensure all wire connections are secure and protected from moisture and abrasion.
Muntatge de canonada
- Identify a suitable pipe or pole for mounting. The light is designed to fit standard pipe sizes.
- Use the provided hardware to secure the light base to the pipe.
- Route the power wires and connect them as described in the Permanent Surface Mount section.
Note: Professional installation is recommended if you are unfamiliar with vehicle electrical systems.
Instruccions de funcionament
The Wolo Apollo 8 features eight (8) selectable warning light patterns.
- Once the light is powered on, it will activate in the last selected flash pattern.
- To change the flash pattern, momentarily press the pattern selection button (located on the unit or via a control wire).
- Each press of the button will cycle to the next available warning light pattern.
- Release the button when the desired pattern is displayed. The light will retain this pattern until changed again or power is disconnected.
Manteniment
- Neteja: Clean the clear polycarbonate lens periodically with a soft cloth and mild soap solution. Avoid abrasive cleaners or solvents that could damage the lens.
- Substitució de la lent: The lens is replaceable. If the lens becomes damaged, contact Wolo customer support for replacement parts and instructions.
- Inspecció del cablejat: Periodically inspect all wiring and connections for signs of wear, corrosion, or damage. Ensure connections remain secure.
- The GEN 3 LEDs are designed for long life and are maintenance-free, requiring no bulb replacement.
Resolució de problemes
| Problema | Causa possible | Solució |
|---|---|---|
| La llum no il·lumina | Sense font d'alimentació | Check power connections, fuse, and vehicle battery. Ensure the light is receiving 12-60V DC. |
| Light flashes erratically | Loose wiring connection or incorrect voltage | Inspect all wiring connections for tightness. Verify input voltage is within the 12-60V DC range. |
| Cannot change flash pattern | Faulty pattern selection button or control circuit | Ensure the button is functioning correctly. If the issue persists, contact customer support. |
| Reducció de la producció de llum | Lent bruta | Clean the lens with a soft cloth and mild soap solution. |
Especificacions tècniques
- Model: 3095PPM-C
- Font de llum: 20 x 1-watt GEN 3 LEDs
- Vol. Operatiutage: 12 - 60 volts de corrent continu
- Peak Current Draw: 1.37 Amps
- Light Patterns: 8 selectable patterns
- Material de la lent: Polycarbonate Plastic (Clear)
- Material base: Aluminum (Painted Black)
- Opcions de muntatge: Permanent Surface Mount, Pipe Mount
- Característiques especials: Waterproof, Encapsulated Microprocessor, Reduced EMI
- Dimensions: Aproximadament 6.63 x 6.75 x 6.5 polzades
- Pes: Aproximadament 1.85 lliures
Garantia i Suport
Wolo products are designed for durability and performance. For specific warranty details, please refer to the warranty card included with your product or visit the official Wolo weblloc.
Atenció al client
For technical assistance, replacement parts, or warranty claims, please contact Wolo customer support.
Wolo Manufacturing Corp.
Deer Park, NY 11729
