Introducció
This manual provides essential information for the proper use and installation of the Estes Launch Lug Pack. These components are designed to ensure vertical stability for model rockets during liftoff when used with compatible launch pad rods.
Informació de seguretat
WARNING: This product is not a toy. Recommended for ages 14 and older.
Always follow all safety guidelines provided with your model rocket kit and launch system. Ensure proper adult supervision for users under 18 years of age.
Producte acabatview
The Estes Launch Lug Pack (Model 302320) contains a variety of launch lugs designed for different model rocket sizes. These lugs are small, hollow tubes that slide over a launch rod, guiding the rocket during the initial phase of flight.
Figure 1: Contents of the Estes Launch Lug Pack. The image displays multiple white plastic tubes of different diameters, which are the launch lugs.
El pack inclou:
- Eight (8) launch lugs with 1/8-inch diameter.
- Four (4) launch lugs with 3/16-inch diameter.
- Two (2) launch lugs with 1/4-inch diameter.
Configuració i instal·lació
- Select Appropriate Lug Size: Choose a launch lug that matches the diameter of your launch rod. The lug should slide freely over the rod without excessive play.
- Determinar la ubicació: Launch lugs are typically attached to the rocket body tube. Most rocket kits provide specific locations for lug placement. Generally, two lugs are used: one near the top of the rocket and one near the bottom, ensuring stable guidance.
- Mètode adjunt:
- Adhesiu: Apply a suitable model rocket adhesive (e.g., plastic cement, white glue, or epoxy) to the contact surface of the lug and the rocket body. Ensure a strong bond.
- Tape (Temporary/Light Models): For very light models or temporary setups, strong adhesive tape can be used to secure the lugs. However, adhesive is generally recommended for permanent attachment.
- Temps de curat: Allow sufficient time for the adhesive to cure completely before handling or launching the rocket. Refer to the adhesive manufacturer's instructions for specific curing times.
- Prova d'ajust: Before final assembly, slide the chosen launch lug onto your launch rod to confirm a smooth fit.
Principis de funcionament
During a model rocket launch, the launch lugs serve as guides. The launch rod passes through the lugs, keeping the rocket aligned vertically until it achieves sufficient speed for its fins to provide aerodynamic stability. This prevents the rocket from veering off course immediately after ignition.
Ensure the launch rod is clean and free of obstructions to allow the lugs to slide smoothly during liftoff.
Manteniment
- Inspecció: Before each launch, inspect the launch lugs for any signs of damage, cracks, or loose attachment. Replace damaged lugs immediately.
- Neteja: Keep the lugs clean and free of debris, dirt, or adhesive residue that could impede smooth movement on the launch rod.
- Emmagatzematge: Store unused launch lugs in a cool, dry place away from direct sunlight to prevent material degradation.
Resolució de problemes
- Lug does not slide smoothly on launch rod:
- Ensure the correct lug diameter is selected for the launch rod.
- Check for debris or adhesive residue inside the lug or on the rod. Clean as necessary.
- Inspect the lug for deformities. Replace if damaged.
- Lug detaches during launch:
- Verify that a strong, appropriate adhesive was used for attachment.
- Ensure sufficient curing time was allowed for the adhesive.
- Re-attach with fresh adhesive, ensuring proper surface preparation.
Especificacions
| Número de model | 302320 |
| Marca | Estes |
| Material | Plàstic |
| Components inclosos | 16 Launch Lugs (8x 1/8", 4x 3/16", 2x 1/4") |
| Dimensions del paquet (L x W x H) | 6.5 x 3.4 x 0.4 polzades (16.51 x 8.64 x 1.02 cm) |
| Pes de l'article | 0.01 unces (0.28 grams) |
| Edat recomanada | 14+ (as per safety information) |
| UPC | 047776023208, 047776099487 |
Informació de la garantia
Estes products are manufactured to high-quality standards. For specific warranty details, please refer to the documentation included with your original model rocket kit or visit the official Estes website. Generally, components like launch lugs are considered consumables or replacement parts and may not carry an extended warranty.
Atenció al client
For further assistance, technical support, or inquiries regarding Estes products, please visit the official Estes weblloc web o poseu-vos en contacte amb el seu departament d'atenció al client. La informació de contacte normalment es pot trobar a l'embalatge del producte o al fabricant. weblloc.
També podeu visitar el Estes Store on Amazon per obtenir més informació sobre el producte.
