Introducció
This manual provides essential instructions for the setup, operation, and maintenance of your Pro-Ject RM 1.3 Turntable. Please read it thoroughly before use to ensure proper functionality and longevity of your device.
Contingut del paquet
Abans de continuar amb la configuració, comproveu que hi hagi tots els components:
- Pro-Ject RM 1.3 Turntable Unit
- Plat
- Cinturó de seguretat
- Outboard 15V AC Motor
- Font d'alimentació
- Sumiko Pearl Cartridge (pre-installed or separate)
- Removable RCA Cables
- Contrapès
- Pes antipatinatge
- Manòmetre de pressió amb llapis
Instruccions de configuració
Follow these steps carefully to set up your turntable:
- Desembalatge: Carefully remove all components from the packaging. Retain packaging for future transport.
- Instal·lació de la safata: Place the platter onto the central spindle. Ensure it sits securely and rotates freely.
- Col·locació del motor: Position the outboard motor unit next to the turntable chassis. The motor pulley should align with the outer rim of the platter.
- Drive Belt Installation: Gently stretch the drive belt around the motor pulley and the outer rim of the platter. Ensure the belt is not twisted.
- Cartridge Installation (if not pre-installed): If your Sumiko Pearl cartridge is not pre-installed, carefully attach it to the tonearm headshell using the provided screws. Ensure correct alignment.
- Counterweight Adjustment: Slide the counterweight onto the rear of the tonearm. Adjust it until the tonearm floats horizontally. Then, set the tracking force according to the cartridge manufacturer's recommendations (typically 1.8g for Sumiko Pearl). Use a stylus pressure gauge for accuracy.
- Anti-skating Adjustment: Attach the anti-skating weight to the tonearm's anti-skating mechanism. Adjust the setting to match the tracking force.
- Connectant a Ampmés viu: Connect the removable RCA cables from the turntable's output to the "Phono" input of your amplifier or a dedicated phono preamplifier. Ensure the ground wire is connected between the turntable and your ampmés viu / preamplifier to minimize hum.
Instruccions de funcionament
- Encès: Connect the power supply to the motor unit and a wall outlet. Press the power button on the motor unit to start the platter rotation.
- Seleccioneu la velocitat: Most turntables offer 33 1/3 RPM and 45 RPM. Ensure the correct speed is selected for your record. (Refer to motor unit for speed selection mechanism, typically a switch or belt position change).
- Registre del lloc: Carefully place your vinyl record onto the platter.
- Braç inferior: Gently lift the tonearm using the cueing lever. Position the stylus over the desired track on the record. Slowly lower the cueing lever to allow the stylus to descend onto the record groove.
- Reproducció: The record will now play. Adjust the volume on your ampmés viu.
- Aturant la reproducció: At the end of the record, or when you wish to stop, use the cueing lever to lift the tonearm from the record. Return the tonearm to its rest and secure it. Press the power button on the motor unit to stop the platter.
Manteniment
- Neteja de discos: Regularly clean your vinyl records using a dedicated record brush or cleaning solution to remove dust and static.
- Cura del stylus: Use a soft stylus brush to gently clean the stylus tip before and after each play. Brush from back to front. Avoid touching the stylus with your fingers.
- Neteja del tocadiscs: Wipe the turntable chassis and platter with a soft, dry, lint-free cloth. Avoid abrasive cleaners or solvents.
- Inspecció del cinturó: Periodically check the drive belt for wear or stretching. Replace if necessary to maintain accurate playback speed.
Resolució de problemes
Si teniu problemes amb el tocadiscos, consulteu els següents problemes i solucions habituals:
| Problema | Causa possible | Solució |
|---|---|---|
| No power / Platter not spinning | Power cable disconnected; faulty power supply/motor; power outlet issue. | Ensure power cable is securely connected. Test the power outlet with another device. If the issue persists, contact support. |
| So de brunzit o brunzit | Ground wire not connected; proximity to other electronics; faulty cabling; internal wiring issue. | Ensure the ground wire is securely connected between the turntable and ampmés viu / preamplifier. Move the turntable away from other electronic devices. Check RCA cables for damage. If hum persists, it may indicate an internal grounding issue requiring professional service. |
| Distorted sound / Skipping | Incorrect tracking force; worn or dirty stylus; damaged record; incorrect anti-skating. | Re-adjust tracking force and anti-skating. Clean the stylus. Inspect the record for damage. Replace stylus if worn. |
| Velocitat de reproducció incorrecta | Incorrect speed selection; worn or stretched drive belt. | Verify the correct speed setting. Inspect and replace the drive belt if it appears worn or loose. |
Especificacions
| Característica | Detall |
|---|---|
| Marca | Pro-Ject |
| Model | RM 1.3 |
| Dimensions del producte | 15 x 4.33 x 13.78 polzades |
| Pes de l'article | 11.15 lliures |
| Components inclosos | Sumiko Pearl Cartridge, removable RCA cables |
| Tipus de motor | Motor AC |
| Format del senyal | Analògic |
| Voltage | 15 volts (CA) |
| Color | Negre |
Garantia i Suport
For warranty information, please refer to the documentation provided with your purchase or visit the official Pro-Ject website. For technical support or service inquiries, please contact your authorized Pro-Ject dealer or the manufacturer's customer service department.
Conserveu el vostre comprovant de compra per a reclamacions de garantia.
