Einhell TC-MS 2112 T Miter and Table Saw

1. Introducció

This manual provides essential information for the safe and effective operation, setup, and maintenance of your Einhell TC-MS 2112 T Miter and Table Saw. Please read all instructions carefully before using the tool to ensure personal safety and optimal performance. Keep this manual in a safe place for future reference.

2. Instruccions de seguretat

Advertències generals de seguretat d'eines elèctriques:

• Utilitzeu sempre l'equip de protecció individual adequat, com ara ulleres de seguretat, protecció auditiva i una màscara antipols.
• Assegureu-vos que la zona de treball estigui neta, ben il·luminada i lliure d'obstacles.
• Mantenir els nens i els espectadors allunyats de la zona d'operacions.
• No feu servir eines elèctriques en atmosferes explosives, com ara en presència de líquids, gasos o pols inflamables.
• Eviteu l'arrencada accidental. Assegureu-vos que l'interruptor estigui en la posició d'apagada abans de connectar l'eina a la xarxa elèctrica, agafar-la o transportar-la.
• Mantenir un bon peu i un equilibri en tot moment.
• Desconnecteu l'endoll de la font d'alimentació abans de fer qualsevol ajust, canviar accessoris o emmagatzemar eines elèctriques.

Specific Miter and Table Saw Safety Warnings:

• Always use the push stick when operating in table saw mode, especially for narrow workpieces.
• Ensure the blade guard is in place and functioning correctly before each use.
• No introduïu mai les mans a la zona de la fulla mentre la serra estigui en funcionament o connectada a la xarxa elèctrica.
• Secure the workpiece firmly before cutting. Do not attempt to hand-hold small pieces.
• Use only sharp, correctly sized saw blades suitable for the material being cut.
• Deixeu que la fulla arribi a la màxima velocitat abans de començar a tallar.
• Never remove cut-off pieces or other parts of the workpiece from the cutting area while the blade is running.

3. Producte acabatview

The Einhell TC-MS 2112 T is a versatile 2-in-1 tool, functioning as both a miter saw and a table saw, designed for precise cutting of wood and similar materials.

Figura 3.1: global view of the Einhell TC-MS 2112 T Miter and Table Saw.

Figure 3.2: Close-up of the miter scale and model designation on the saw base.

Figura 3.3: View of the integrated table extension for supporting longer workpieces.

Figure 3.4: The parallel guide, used for consistent rip cuts in table saw mode.

4. Muntatge i muntatge

Before initial use, ensure all components are present and undamaged. Refer to the packing list for verification.

1. Desembalatge: Carefully remove the saw and all accessories from the packaging. Retain packaging for potential future transport or storage.
2. Estabilitat de la base: Place the saw on a stable, level workbench. Secure the saw to the workbench using appropriate fasteners through the mounting holes in the base to prevent movement during operation.
3. Instal·lació de la fulla (si no està preinstal·lada): Ensure the saw is unplugged. Follow the instructions for safely installing the 210mm saw blade, ensuring the rotation direction matches the arrow on the saw.
4. Control de guàrdia: Verify that all blade guards move freely and return to their protective positions automatically.
5. Extensions de taula: Extend the workpiece supports (extensions) as needed for longer materials.

5. Instruccions de funcionament

The Einhell TC-MS 2112 T offers both miter saw and table saw functionalities. Always select the appropriate mode for your cutting task.

5.1. Miter Saw Function

For cross-cutting and angle cuts on workpieces.

1. Ajust de l'angle del bisell: Loosen the locking knob for the turntable. Rotate the turntable to the desired angle (up to 45° left or right). Securely tighten the locking knob.
2. Ajust de l'angle del bisell: Loosen the locking mechanism for the saw head. Tilt the saw head to the desired bevel angle (up to 45° to the left). Securely tighten the locking mechanism.
3. Positioning Workpiece: Place the workpiece firmly against the fence and the turntable. Use clamps si cal.
4. Fent el tall: Depress the safety switch and then the main power switch. Allow the blade to reach full speed. Slowly lower the saw head through the workpiece. Once the cut is complete, release the power switch and allow the blade to stop before raising the saw head.

Figure 5.1: Demonstrating the miter saw function for angled cuts.

Figure 5.2: Illustration of a 90° x 90° cross-cut (max. 120 x 55 mm).

Figure 5.3: Illustration of a 90° x 45° miter cut (max. 65 x 55 mm).

Figure 5.4: Illustration of a 45° x 45° compound miter cut (max. 40 x 23 mm).

5.2. Table Saw Function

For ripping and sizing workpieces.

1. Converting to Table Saw: Ensure the saw head is locked in the upright position. Adjust the blade height using the appropriate mechanism.
2. Ajust de l'alçada de la fulla: Use the height adjustment knob to set the desired blade exposure above the table (0-33 mm).
3. Using Parallel Guide: Position the parallel guide to achieve the desired cutting width. Securely lock the guide in place.
4. Positioning Workpiece: Place the workpiece on the table, ensuring it is flat and against the parallel guide.
5. Fent el tall: Depress the safety switch and then the main power switch. Allow the blade to reach full speed. Using the push stick, slowly feed the workpiece through the blade. Never use your hands to push the workpiece directly into the blade.

Figure 5.5: Demonstrating the table saw function for rip cuts.

Figure 5.6: Close-up of the blade height adjustment for table saw mode.

Figure 5.7: The included push stick, essential for safe table saw operation.

5.3. Extracció de pols

The saw is equipped with a dust extraction port to connect to a vacuum cleaner or dust extractor, helping to keep the work area clean and reduce airborne dust.

Figure 5.8: The dust extraction port for connecting a vacuum system.

6. Manteniment

Un manteniment regular garanteix la longevitat i el funcionament segur de la serra.

• Neteja: After each use, disconnect the saw from power and clean off dust and debris using a brush or compressed air. Do not use harsh chemicals.
• Substitució de la fulla: When the saw blade becomes dull or damaged, replace it with a new, sharp blade of the correct size (210mm diameter, 30mm bore). Always unplug the saw and use appropriate tools for safe blade removal and installation.
• Lubricació: Periodically apply a light machine oil to moving parts and pivot points to ensure smooth operation.
• Inspecció: Regularly inspect the power cord, plug, switches, and guards for any signs of damage or wear. Replace damaged parts immediately.
• Emmagatzematge: Guardeu la serra en un lloc sec i segur, fora de l'abast dels nens.

7. Solució De Problemes

Aquesta secció tracta problemes comuns que podeu trobar.

8. Especificacions

Technical data for the Einhell TC-MS 2112 T Miter and Table Saw.

Figure 8.1: Blade specifications.

Figure 8.2: Max cut depth.

Figure 8.3: Height adjustment range.

Figure 8.4: Product weight.

9. Garantia

This Einhell product is covered by a manufacturer's warranty. Please refer to the warranty card included with your purchase or visit the official Einhell weblloc web per obtenir els termes i condicions detallats sobre la cobertura de la garantia i les reclamacions.

10. Atenció al client

For technical assistance, spare parts, or further information, please contact Einhell customer service or visit their official weblloc:

• Weblloc: www.einhell.com
• Informació de contacte: Consulteu la secció de contacte del lloc web oficial weblloc web per obtenir detalls de suport regional.