Producte acabatview
The VF Series Two-Way, Spring-Return, Low-Pressure D-3000 Series Pneumatically Actuated, Standard-Pressure, Standard-Temperature Butterfly Valves are specifically designed for a wide range of HVAC applications. These include two-position and modulating control of hot, chilled, or condenser water, and 50/50 glycol solutions. The valves are bidirectional, ensuring positive shutoff with flow in either direction.
Figure 1: VFC-030HB Butterfly Valve with Actuator. This image displays the complete valve assembly, including the butterfly valve body and the attached pneumatic actuator with positioner, designed for precise flow control in HVAC systems.
Informació de seguretat
Always adhere to local codes and regulations during installation and operation. Ensure all power and pressure sources are disconnected before performing any maintenance or installation procedures. Wear appropriate personal protective equipment (PPE). This valve operates under pressure and contains moving parts; exercise caution to prevent injury.
Configuració i instal·lació
Proper installation is crucial for the optimal performance and longevity of the valve. Consult relevant piping and electrical diagrams before beginning installation.
- Comprovació prèvia a la instal·lació: Verify that the valve model and size match the system requirements. Inspect the valve for any shipping damage.
- Orientació de muntatge: The valve can be mounted in any orientation, but ensure adequate clearance for maintenance and actuator access.
- Connexió de canonades: Install the valve between flanges using appropriate gaskets and fasteners. Ensure proper alignment to prevent stress on the valve body. The valve is bidirectional; flow direction does not impact shutoff.
- Connexió pneumàtica: Connect the pneumatic supply lines to the actuator's designated ports. Ensure the air supply is clean, dry, and within the specified pressure range for the actuator.
- Electrical Connection (for Positioner): If equipped with a positioner, connect the control signal wiring (e.g., 4-20mA, 0-10V) and power supply according to the positioner's specific wiring diagram. Ensure proper grounding.
- Prova de fuites: After installation, slowly pressurize the system and check all connections for leaks.
- Actuator Calibration: Calibrate the proportional control actuator and positioner according to the manufacturer's instructions to ensure accurate valve positioning and control. This typically involves setting the zero and span points.
Instruccions de funcionament
The VFC-030HB valve is designed for both two-position (open/closed) and modulating control, providing precise regulation of fluid flow.
- Two-Position Control: For simple open/closed operation, the actuator will drive the valve to its fully open or fully closed position based on the control signal or pneumatic supply. The spring-return mechanism ensures the valve returns to its default (spring open) position upon loss of pneumatic pressure.
- Control de modulació: When used with a proportional control actuator and positioner, the valve can be positioned anywhere between fully open and fully closed. The positioner interprets an analog control signal (e.g., 4-20mA or 0-10V) and adjusts the air pressure to the actuator to achieve the desired valve opening.
- Bidirectional Flow: The valve is designed to provide positive shutoff regardless of the flow direction. This eliminates the need for specific upstream/downstream installation.
- Accionament manual (si escau): Some actuators may include a manual override mechanism. Refer to the actuator's specific manual for instructions on safe manual operation.
Manteniment
Regular maintenance ensures reliable operation and extends the lifespan of the valve. Always depressurize the system and disconnect power/pneumatic supply before performing maintenance.
- Inspecció periòdica: Visually inspect the valve and actuator for any signs of wear, corrosion, or damage. Check for leaks around the valve body and connections.
- Actuator Air Supply: Ensure the pneumatic air supply remains clean and dry. Contaminants can damage the actuator and positioner. Regularly check and drain air filters/dryers in the pneumatic system.
- Linkage and Fasteners: Check all bolts, nuts, and linkages connecting the actuator to the valve for tightness. Re-tighten if necessary, but do not overtighten.
- Comprovació del funcionament de la vàlvula: Periodically cycle the valve through its full range of motion to ensure smooth operation and proper seating.
- Neteja: Keep the exterior of the valve and actuator clean. Avoid using harsh chemicals that could damage seals or coatings.
Resolució de problemes
Aquesta secció ofereix orientació per a problemes comuns. Per a problemes complexos, poseu-vos en contacte amb personal de servei qualificat.
| Problema | Causa possible | Solució |
|---|---|---|
| Valve not opening/closing fully | Insufficient pneumatic pressure; Actuator/positioner malfunction; Obstruction in valve; Incorrect calibration. | Check air supply pressure; Inspect actuator/positioner; Check valve for debris; Recalibrate positioner. |
| Valve leaking | Damaged seals/gaskets; Improper installation; Valve not fully closing. | Inspect and replace seals/gaskets; Re-check installation alignment; Verify full closure and recalibrate if needed. |
| Inaccurate valve positioning | Positioner calibration error; Control signal issue; Mechanical binding. | Recalibrate positioner; Verify control signal integrity; Check for mechanical interference. |
| No response from actuator | No pneumatic supply; No electrical power (for positioner); Damaged control wiring. | Check pneumatic supply; Verify power to positioner; Inspect control wiring for breaks. |
Especificacions
| Atribut | Valor |
|---|---|
| Dimensions del paquet | 6 x 6 x 5 polzades; 9.6 unces |
| Número de model de l'article | VFN-030HB-001A |
| Data de primera disponibilitat | 17 de maig de 2019 |
| Fabricant | Johnson Controls, Inc |
| Marca | Johnson Controls |
| Tipus de connexió d'entrada | Premeu |
| Número d'identificació comercial global | 10785028573183 |
Garantia i Suport
For specific warranty terms and conditions, please refer to the official documentation provided by Johnson Controls at the time of purchase or visit the official Johnson Controls website. Warranty coverage typically varies by region and product type.
For technical support, service, or replacement parts, please contact Johnson Controls customer service or an authorized distributor. Contact information can usually be found on the manufacturer's official weblloc web o a la documentació de la compra.
