1. Producte acabatview
The Defiant 180 Degree Black Motion-Sensing Outdoor Security Light is designed to provide enhanced security and illumination for outdoor areas such as driveways and garages. This unit features advanced technology including DualBrite 2-Level Lighting, Alert Flash Security, and Bulb Life Extending Technology, ensuring efficient and reliable operation.
Les característiques clau inclouen:
- DualBrite 2-Level Lighting: Offers accent lighting when no motion is present and full bright light for security when motion is detected.
- Selectable Motion Timer: Adjustable settings (test, 1, 5, 10 minutes) to optimize energy usage.
- Compatibilitat amb bombetes: Uses 2 - 120-Watt PAR 38-bulbs (not included), compatible with PAR38 incandescent and select PAR38 dimmable LED outdoor rated-wet rated bulbs.
- Construcció duradora: Designed for long-lasting outdoor operation with light shields for bulb protection.
2. Informació de seguretat
Si us plau, llegiu i enteneu totes les instruccions abans de començar la instal·lació. Si no seguiu aquestes instruccions, podeu patir descàrregues elèctriques, incendis o altres perills que podrien causar lesions o danys materials.
- ADVERTIMENT: Risc de descàrrega elèctrica. Desconnecteu l'alimentació al fusible o al disjuntor abans d'instal·lar o fer el servei.
- ADVERTIMENT: Risk of fire. Keep combustible materials away from the lamp.
- This fixture is intended for use with 120V/60Hz power supply.
- Totes les connexions de cablejat han de complir els codis elèctrics locals.
- Do not install near flammable surfaces or materials.
- Assegureu-vos que el dispositiu estigui fixat correctament a una superfície adequada.
- Do not look directly into the light source when illuminated.
3. Contingut del paquet
Verifiqueu que tots els components siguin presents abans de començar la instal·lació:
- Defiant 180 Degree Motion-Sensing Outdoor Security Light
- Maquinari de muntatge (cargols, femelles, junta)
- Manual d'instruccions
Note: PAR38 bulbs are not included and must be purchased separately.
4. Especificacions
| Especificació | Detall |
|---|---|
| Número de model | DF-5416-BK |
| Font d'alimentació | Elèctric amb cable |
| Voltage | 110 Volts |
| Tipus de bombeta | PAR38 Incandescent or Dimmable LED (not included) |
| Max Wattage per Bulb | 120 watts |
| Interval del sensor de moviment | 180 graus |
| Ús interior/exterior | A l'aire lliure |
| Tipus d'instal·lació | Muntat a la paret |
| Dimensions (L x A x A) | 8 x 14 x 12.5 polzades |
| Pes de l'article | 1.75 lliures |
| Nivell de resistència a l'aigua | Resistent a l'aigua |
5. Configuració i instal·lació
Before starting, ensure the power to the installation area is turned OFF at the circuit breaker or fuse box.
5.1 Muntatge de l'aparell
The security light is designed for wall-mounted installation. Choose a location that provides optimal coverage for the motion sensor and light output.
- Carefully remove the mounting plate from the back of the fixture.
- Position the mounting plate over the junction box and mark the screw holes.
- Secure the mounting plate to the wall using the provided mounting hardware. Ensure it is firmly attached.
- Feu passar els cables elèctrics de la caixa de connexions pel forat central de la placa de muntatge.
Figura 5.1: Frontal view of the security light, showing the two lamp heads and the motion sensor unit.
Figura 5.2: lateral view illustrating the adjustable arm and the mounting bracket for wall installation.
5.2 Connexions de cablejat
Connect the wires according to standard electrical practices. If you are unsure, consult a qualified electrician.
- Connecteu el negre cable des del dispositiu fins al negre cable (calent) de la caixa de connexions amb una femella.
- Connecteu el blanc cable des del dispositiu fins al blanc cable (neutre) de la caixa de connexions amb una femella.
- Connecteu el verd or bare coure (ground) wire from the fixture to the ground wire from the junction box using a wire nut.
- Introduïu amb cura tots els cables a la caixa de connexió.
5.3 Attaching the Fixture Body and Installing Bulbs
- Align the fixture body with the mounting plate and secure it with the provided screws. Ensure the gasket is properly seated to prevent water intrusion.
- Screw two PAR38 bulbs (up to 120W each, not included) into the lamp suports. No els estrenyeu massa.
6. Instruccions de funcionament
Once installed and powered on, the security light can be configured for optimal performance.
6.1 Ajust de Lamp Heads and Sensor
El lamp heads and motion sensor are adjustable to direct light and detection where needed.
- Loosen the adjustment knobs on the lamp heads and sensor.
- Gira la lamp heads to illuminate the desired area.
- Angle the motion sensor to cover the desired detection zone (up to 180 degrees).
- Tighten the adjustment knobs to secure their positions.
Figure 6.1: Detail of the motion sensor and its adjustable controls.
6.2 Setting the Motion Timer
The motion timer determines how long the light stays on after motion is detected and stops. The available settings are Test, 1, 5, and 10 minutes.
- Locate the "TIME" dial on the bottom of the motion sensor.
- Rotate the dial to select the desired duration:
- Prova: For initial setup and aiming. Light stays on for a few seconds.
- 1 min: Light stays on for 1 minute after motion ceases.
- 5 min: Light stays on for 5 minutes after motion ceases.
- 10 min: Light stays on for 10 minutes after motion ceases.
6.3 DualBrite 2-Level Lighting
This feature provides a low-level accent light during darkness, which brightens to full intensity upon motion detection.
- Locate the "DUALBRITE" dial on the bottom of the motion sensor.
- Rotate the dial to activate or deactivate this feature, and to adjust the duration of the low-level accent light (if applicable, refer to specific product manual for detailed settings).
- When activated, the light will illuminate at a low level from dusk to dawn, and switch to full brightness when motion is detected.
7. Manteniment
Un manteniment regular garanteix la longevitat i el rendiment òptim del vostre llum de seguretat.
- Neteja: Netegeu periòdicament l'aparell amb un drap suau iamp cloth. Do not use abrasive cleaners or solvents. Ensure the motion sensor lens is clear of dirt and debris for proper operation.
- Substitució de bombetes:
- Desconnecteu l'alimentació de l'aparell a l'interruptor.
- Deixeu que les bombetes es refredin completament abans de manipular-les.
- Unscrew the old PAR38 bulb and screw in a new one (up to 120W).
- Restaura l'alimentació i prova.
- Inspeccions: Annually inspect wiring connections and mounting hardware for any signs of wear, corrosion, or loosening.
8. Solució De Problemes
If your security light is not functioning as expected, refer to the following common issues and solutions:
| Problema | Causa possible | Solució |
|---|---|---|
| Light does not turn on at all. | No power; faulty bulb; wiring issue. | Check circuit breaker/fuse. Replace bulbs. Verify wiring connections. |
| La llum es manté encesa contínuament. | Sensor in "Test" mode; constant motion detected; wiring error. | Adjust "TIME" dial off "Test". Clear obstructions from sensor view. Recheck wiring. |
| La llum s'encén durant el dia. | Photocell blocked or faulty. | Ensure photocell (small clear dome on sensor) is not obstructed by dirt or objects. |
| El sensor de moviment no detecta. | Sensor obstructed; incorrect angle; sensitivity too low. | Clean sensor lens. Adjust sensor angle. Increase sensitivity (if applicable, refer to product specific controls). |
9. Garantia i Suport
This Defiant product is backed by a manufacturer's warranty. For specific warranty details, including duration and coverage, please refer to the warranty card included with your purchase or visit the official Defiant weblloc.
For technical support, replacement parts, or further assistance, please contact Defiant customer service. Contact information can typically be found on the product packaging or the manufacturer's weblloc.
Recursos en línia: For additional information, FAQs, or video tutorials, please visit the official Defiant support page. Defiant Lighting Products
