Watts LF-MMV-M1-UT Thermostatic Mixing Valve User Manual

1. Producte acabatview

The Watts LF-MMV-M1-UT is a 1-inch thermostatic mixing valve designed to precisely control water temperature. It features FPT (Female Pipe Thread) union connections and allows for an adjustable temperature range from 80 degrees to 120 degrees Fahrenheit, with a flow rate capacity of 0.5 to 12 GPM. This valve utilizes a solid wax hydraulic principle thermostat to ensure dependable mixing of hot and cold fluids, providing a consistent and safe mixed water temperature. It also incorporates integral check valves and filter washers to prevent cross-flow and restrict mixed water flow if the cold water supply is compromised, enhancing safety.

Figure 1: Watts LF-MMV-M1-UT Thermostatic Mixing Valve. This image displays the brass valve body with three ports and union connections, topped by a light-colored adjustment cap.

2. Informació de seguretat

ADVERTIMENT: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Always follow local plumbing codes and regulations during installation and operation.

• Ensure all water supplies are shut off before installation or maintenance.
• Utilitzeu equips de protecció individual (EPI) adequats, com ara guants i ulleres de protecció.
• No supereu la pressió màxima de funcionament de 150 PSI.
• Verify that the mixed water temperature is safe for its intended application, especially in domestic hot water systems to prevent scalding.
• Installation should be performed by a qualified professional in accordance with all applicable codes.

3. Configuració i instal·lació

Proper installation is crucial for the optimal performance and safety of the thermostatic mixing valve. Refer to the diagram below for typical installation orientation.

3.1 Comprovacions prèvies a la instal·lació

1. Inspect the valve for any signs of damage.
2. Ensure all necessary plumbing fittings and tools are available.
3. Confirm the water supply lines (hot and cold) are clearly identified.

3.2 Passos d'instal·lació

1. Shut off Water Supply: Turn off the main water supply to the area where the valve will be installed.
2. Drain Lines: Open nearby faucets to drain residual water from the pipes.
3. Connect Valve:
   • Connect the hot water supply to the designated hot inlet (typically marked 'H' or 'HOT').
   • Connect the cold water supply to the designated cold inlet (typically marked 'C' or 'COLD').
   • Connect the mixed water outlet to the distribution system (typically marked 'M' or 'MIX').

   The valve features FPT union connections for ease of installation and removal.

4. Connexions segures: Use appropriate pipe sealant or PTFE tape on all threaded connections to ensure a watertight seal. Tighten connections securely but do not overtighten.
5. Restaurar el subministrament d'aigua: Slowly turn on the main water supply and check for leaks.
6. Aire de purga: Open faucets downstream to purge air from the system until water flows smoothly.

4. Instruccions de funcionament

The Watts LF-MMV-M1-UT valve is designed for automatic temperature regulation. Once installed, its primary operation involves setting the desired mixed water temperature.

4.1 Ajust de temperatura

1. Locate Adjustment Cap: The valve has an adjustment cap on top.
2. Ajustar la temperatura: Rotate the adjustment cap to increase or decrease the mixed water temperature. A thermometer should be used at the point of use to verify the desired temperature.
3. Verifica la temperatura: Allow water to flow for a few minutes to stabilize the temperature before making final adjustments. The adjustable range is 80°F to 120°F.

The valve's internal thermostat automatically adjusts the hot and cold water flow to maintain the set temperature, even with fluctuations in supply pressures or temperatures.

5. Manteniment

Regular maintenance is generally not required for this thermostatic mixing valve under normal operating conditions. However, periodic checks can ensure continued optimal performance.

• Annual Temperature Check: It is recommended to annually verify the mixed water temperature with a thermometer to ensure it remains within the desired and safe range.
• Inlet Strainers/Check Valves: The valve includes integral filter washers and check valves. If flow issues or inconsistent temperatures occur, these components may need inspection and cleaning. This typically requires shutting off water, disassembling the union connections, and carefully removing and cleaning the screens/check valve components.
• Inspecció de fuites: Periodically inspect all connections for any signs of leaks. Address any leaks immediately.

6. Solució De Problemes

7. Especificacions

8. Garantia i Suport

For specific warranty information and technical support, please refer to the official Watts website or contact Watts customer service directly. Keep your purchase receipt for warranty claims.

Watts Customer Service: For assistance with installation, operation, or troubleshooting, please visit the Watts official weblloc or consult your local distributor.