1. Introducció
This manual provides essential information for the proper installation, operation, and maintenance of your X-PRO 50cc 4-Stroke GY6 Scooter Engine. This engine is designed for 50cc GY6 scooters and features an automatic CVT transmission with both electric and kick start capabilities. Please read this manual thoroughly before attempting any procedures to ensure safe and efficient use.
Figura 1: Frontal view of the X-PRO 50cc 4-Stroke GY6 Scooter Engine.
2. Configuració i instal·lació
Careful attention during installation is crucial for the engine's performance and longevity. This engine is a short case GY6 model.
2.1 Comprovació de compatibilitat
- Longitud de l'eix: This engine is a short shaft model. Verify compatibility with your scooter's frame and existing components before installation.
- Electrical Plug-in: The electrical connector configuration may vary. Compare the engine's plug-in with your scooter's wiring harness. If they are not compatible, an additional adapter or modification may be required. Consult a qualified technician if you are unsure.
Figure 2: Detail of the engine's electrical connectors. Ensure compatibility with your scooter's harness.
2.2 Comprovacions prèvies a la instal·lació
- Inspeccionar per danys: Before installation, thoroughly inspect the engine for any signs of shipping damage or missing components.
- Elements de fixació: Verify that all bolts, nuts, and screws are present and securely tightened.
- Nivells de líquids: Check engine oil and ensure it is at the recommended level. Refer to the Specifications section for lubrication capacity and type.
Figura 3: lateral view of the engine, highlighting the electric starter motor.
3. Funcionament
3.1 Fuel Requirements
This engine requires fuel with an octane rating of 87 or higher. For optimal performance and engine longevity, it is strongly recommended to use ethanol-free gasoline. Ethanol can cause damage to fuel system components over time.
3.2 Procediment d'inici
The engine can be started using either the electric starter or the kick starter.
- Ensure the scooter is in neutral or the brake is applied (depending on scooter model safety features).
- Gireu la clau d'encesa a la posició "ON".
- Arrencada elèctrica: Press and hold the electric start button. If the engine does not start immediately, release the button, wait a few seconds, and try again. It may require a few attempts to prime the carburetor on the first start or after extended storage.
- Inici de sessió: Firmly push down on the kick start lever with your foot. Repeat until the engine starts.
- Allow the engine to warm up for a short period before riding.
4. Manteniment
Regular maintenance is essential for the reliable operation and extended lifespan of your engine.
4.1 Oli de motor
- Tipus d’oli: Use SF15W/40-SE lubrication oil.
- Capacitat d'oli: The lubrication capacity is approximately 0.20 Gallons (900ml).
- Interval de canvi d'oli: It is recommended to change the engine oil frequently, typically every 500 to 750 miles, or as specified by your scooter's manufacturer. Regular oil changes are critical for engine health.
- Comprovar el nivell d'oli: Regularly check the engine oil level and top up as needed.
4.2 Inspecció general
- Periodically inspect all hoses, cables, and electrical connections for wear or damage.
- Ensure all fasteners remain tight.
- Keep the engine clean to prevent dirt and debris from affecting performance.
5. Solució De Problemes
This section addresses common issues you might encounter. For complex problems, consult a qualified mechanic.
| Símptoma | Causa possible | Solució |
|---|---|---|
| Engine does not start (Electric or Kick) |
|
|
| Engine runs poorly or dies prematurely |
|
|
| Engine blows oil |
|
|
6. Especificacions
| Característica | Detall |
|---|---|
| Model de motor | 308-999042 |
| Tipus de motor | Single Cylinder, 4-Stroke, 2-Valve |
| Cylinder Working Volume | 0.01 Gallon (49.5ml) |
| Sistema de refrigeració | Refrigerat per aire |
| Mètode d'encesa | CDI |
| Tipus d'encesa | CFW |
| Arrancador | Electric/Kick starter |
| Transmissió | CVT (Automatic) |
| Embragatge | Shoe-type Automatic Centrifugal Dry Clutch |
| Cavalls de força | 2.82HP/6500Rpm (2.1KW/6500Rpm) |
| Màx. Parell | 3.1 Nm/5500 rpm |
| Min. Stable Idle Speed | 1450-1750 r/min |
| Relació de compressió | 10.5:1 |
| Subministrament de combustible | Carburetor Atomization |
| Carburetor Model | PD18J |
| Tipus de carburador | Horizontal Vacuum Carburetor |
| Combustible recomanat | No. >=87# (Ethanol-free recommended) |
| Min. Fuel Consumption | 9.65oz/HP.h (367g/Kw.h) |
| Lubricació | Pressure/splash |
| Lubrication Model | SF15W/40-SE |
| Lubrication Capacity | 0.20 Gallon (900ml) |
| Model de bugia | A7TC |
| Pes de l'article | 39 lliures |
| Material | Metall |
| Ampedat | 50 Amps |
| Voltage | 12 Volts |
Figura 4: View of the engine's CVT transmission cover.
7. Garantia i assistència
For specific warranty information, please refer to the documentation provided with your purchase or contact the seller directly. For technical support or inquiries regarding your X-PRO engine, please visit the official X-PRO website or contact their customer service department. Keep your purchase receipt and engine model number (308-999042) readily available when seeking support.
You can find more information about X-PRO products by visiting the X-PRO Store on Amazon.
