1. Introducció
This manual provides essential information for the safe and efficient installation, operation, and maintenance of your FriFri Fryer Heater. Please read this manual thoroughly before installation and keep it for future reference. This heater is designed for specific FriFri electric fryer models: FFS41, FFS31, FFM31, and FFE31.
2. Producte acabatview
The FriFri Fryer Heater is a high-performance immersion heating element designed for commercial electric fryers. It ensures rapid and consistent oil heating for optimal frying results. Key features and specifications are detailed below:
- Connection Length: 33 mm
- Aplicació: Fregidora elèctrica
- Tipus de fixació: Brida rectangular
- Amplada: 215 mm
- Other Widths: 66 mm, 60 mm
- Tipus d'ús: Escalfador d'immersió
- Amplada de la brida: 52 mm
- Heating Circuit: 106 mm
- Alçada: 298 mm
- Additional Height: 260 mm, 32 mm
- Longitud del cable: 70 mm
- Potència: 11.4 kW
- Espaiat entre forats: 95 mm
- Diàmetre del forat: 6 mm
- Longitud: 310 mm
- Voltage: 230/400 V
Figura 2.1: The FriFri Fryer Heater, an immersion heating element with multiple heating tubes and electrical connections at the top.
Figura 2.2: Dimensional drawing of the FriFri Fryer Heater, showing various measurements including length (L), width (B), heights (H, H1, H2), and flange dimensions (B1, B2).
3. Instruccions de seguretat
Seguiu sempre les precaucions de seguretat següents per evitar lesions o danys a l'equip:
- Ensure the fryer is disconnected from the power supply before any installation, maintenance, or cleaning.
- Installation and replacement should only be performed by qualified personnel.
- Comproveu que el voltage and power ratings of the heater match the fryer's requirements.
- Do not operate the fryer without sufficient oil or liquid covering the heating element. Dry operation will cause severe damage.
- Handle the heating element carefully to avoid bending or damaging the tubes.
- Keep electrical connections dry and free from oil or water.
- Regularly inspect the heater for signs of wear, corrosion, or damage. Replace immediately if any damage is observed.
4. Configuració i instal·lació
This section outlines the general steps for installing the FriFri Fryer Heater. Refer to your specific FriFri fryer model's service manual for detailed instructions.
- Desconnecteu l'alimentació: Ensure the fryer is completely disconnected from the main power supply.
- Escórrer l'oli: If replacing an existing heater, drain all oil from the fryer tank.
- Access Heater: Depending on the fryer model, you may need to remove panels or lift the control head to access the heating element.
- Treure l'escalfador antic: Carefully disconnect the electrical wiring from the old heater. Unfasten any mounting bolts or clamps securing the heater. Gently remove the old heating element from the tank.
- Inspeccioneu la junta/segell: Check the condition of the gasket or seal around the heater flange. Replace if worn or damaged to ensure a watertight seal.
- Instal·lar un escalfador nou: Insert the new FriFri Fryer Heater into the tank, ensuring the flange aligns correctly with the mounting holes. Secure it with the appropriate bolts or clamps, tightening them evenly to create a proper seal.
- Connecteu el cablejat: Reconnect the electrical wiring to the new heater terminals according to the fryer's wiring diagram. Ensure all connections are secure and insulated.
- Prova de fuites: Before restoring power, fill the fryer tank with water (or oil if preferred) to just above the heating element and check for any leaks around the flange. If leaks are present, re-tighten the bolts or replace the gasket.
- Restaura l'alimentació: Once installation is complete and no leaks are detected, restore power to the fryer.
5. Instruccions de funcionament
The FriFri Fryer Heater operates as an integral part of your electric fryer. Its operation is controlled by the fryer's thermostat and control system. Ensure the fryer is filled with oil to the recommended level before activating the heating element.
- Nivell d'oli: Always ensure the oil level is above the minimum fill line and completely covers the heating element before turning on the fryer. Operating the heater without sufficient oil will cause it to overheat and fail.
- Control de temperatura: Set the desired frying temperature using the fryer's thermostat. The heater will automatically activate to reach and maintain this temperature.
- Preescalfament: Allow sufficient time for the oil to preheat to the set temperature before adding food. The 11.4 kW power rating ensures efficient heating.
- Seguiment: Periodically monitor the oil temperature and the heater's performance during operation.
6. Manteniment
Regular maintenance extends the life of your FriFri Fryer Heater and ensures optimal performance.
- Neteja:
- Desconnecteu sempre l'alimentació abans de netejar.
- After draining oil, clean the heating element to remove any accumulated food particles or carbonized residue.
- Use a non-abrasive brush or cloth and appropriate fryer cleaning solutions. Avoid harsh chemicals that could damage the element's surface.
- Rinse thoroughly and ensure the element is dry before refilling the fryer.
- Inspecció:
- Periodically inspect the heating element for signs of pitting, corrosion, cracks, or swelling.
- Check electrical terminals for looseness, discoloration, or signs of arcing.
- Inspect the flange gasket for deterioration or leaks.
- Substitució: Replace the heater if significant damage or reduced performance is observed.
7. Solució De Problemes
This section provides basic troubleshooting steps for common issues related to the heating element. For complex problems, consult a qualified technician.
| Problema | Causa possible | Solució |
|---|---|---|
| L'escalfador no s'encén | No power to fryer; tripped circuit breaker; faulty thermostat; loose wiring; failed heating element. | Check power supply and circuit breaker. Verify thermostat operation. Inspect and secure wiring. Test heater continuity; replace if open circuit. |
| Oil not heating sufficiently | Incorrect thermostat setting; low voltage; partial heater failure; excessive sediment on element. | Adjust thermostat. Verify correct voltage supply. Inspect element for damage. Clean element thoroughly. |
| Oil overheating | Faulty thermostat; stuck contactor. | Replace thermostat. Inspect and replace contactor if necessary. |
| Oil smells burnt / smokes excessively | Excessive food debris on element; old oil; element operating dry. | Clean element. Change oil. Ensure element is fully immersed. |
8. Especificacions
| Atribut | Valor |
|---|---|
| Marca | Divendres |
| Números de model | FFS41, FFS31, FFM31, FFE31 |
| Número de peça del fabricant | 4251188725889 |
| Poder | 11.4 kW |
| Voltage | 230/400 V |
| Longitud de connexió | 33 mm |
| Fixing Type | Brida rectangular |
| Amplada | 215 mm |
| Espai forat | 95 mm |
| Longitud del cable | 70 mm |
9. Garantia i Suport
For warranty information and technical support, please contact your original point of purchase or an authorized FriFri service center. Information regarding spare parts availability for this specific model is currently unavailable through general product listings. Always use genuine FriFri replacement parts to ensure compatibility and maintain product performance.
For further assistance, you may refer to the official FriFri website or contact their customer service department. (Note: Specific contact details are not provided in the product data.)
