SilverStone Technology ES02-USB

Introducció

The SilverStone ES02-USB is a convenient wireless remote switch kit designed to provide remote control over your computer's power and reset functions. Utilizing standard 2.4GHz RF wireless technology and connecting via the motherboard's USB 2.0 9-pin internal header, this kit allows you to turn on, turn off, or reset your computer from a distance of up to 20 meters in free space. It includes a Y-cable to ensure that your computer case's existing power and reset buttons remain functional alongside the ES02-USB.

This manual provides detailed instructions for the installation, operation, maintenance, and troubleshooting of your ES02-USB kit, along with product specifications.

Contingut del paquet

Si us plau, verifiqueu que tots els elements que s'enumeren a continuació siguin presents al vostre paquet:

• ES02-USB 9-Pin Adapter (Receiver Board)
• Comandament a distància sense fil
• Power / Reset Switch Y-Cable
• Left and Right Angled USB Adapters (Optional use)
• CR2032 Battery (Pre-installed in remote)

Image: The SilverStone ES02-USB kit showing the wireless remote, the receiver board, and the product packaging.

Configuració i instal·lació

Follow these steps to properly install your SilverStone ES02-USB kit:

1. Prepara l'ordinador: Turn off your computer and unplug the power cord from the wall outlet. Open your computer case to access the motherboard.
2. Locate the USB 2.0 9-pin header: Identify an available USB 2.0 9-pin header on your motherboard. This is typically labeled as 'USB', 'F_USB', or similar.
3. Connect the ES02-USB Receiver Board: Plug the ES02-USB receiver board onto the identified USB 2.0 9-pin header. Ensure the orientation is correct to avoid damage. If needed, use the included left or right angled USB adapters for better cable management or clearance.
   

   Image: Close-up of the ES02-USB receiver board, showing the 9-pin connector for motherboard attachment.
4. Connect the Power/Reset Y-Cable:
   • Disconnect your computer case's existing Power SW and Reset SW cables from the motherboard's front panel headers.
   • Connect these disconnected Power SW and Reset SW cables from your case to the corresponding male pins on the ES02-USB Y-cable.
   • Connect the female ends of the ES02-USB Y-cable to the Power SW and Reset SW headers on your motherboard. This setup allows both the remote and your case buttons to function.
   

   Image: The Power SW and Reset SW Y-cables, which allow simultaneous use of the remote and case buttons.

5. Components segurs: Ensure all connections are firm and cables are routed neatly to avoid interference with other components or fans.
6. Tanqueu la carcassa i engegueu-la: Close your computer case, plug the power cord back in, and power on your computer. The ES02-USB is now ready for use.

Image: The complete SilverStone ES02-USB kit, including the remote, receiver board, and the connecting cable, illustrating the components involved in the setup.

Instruccions de funcionament

The ES02-USB remote control features two primary buttons for managing your computer:

• Botó d'encendre (⏻): Press this button to turn your computer on or off. A short press will typically initiate a power-on sequence or a graceful shutdown (depending on your operating system's power settings). A long press (hold for 4-5 seconds) will force a power off.
• Botó de restabliment (↻): Press this button to restart your computer. This functions identically to the physical reset button on your computer case.

The remote operates using 2.4GHz RF wireless technology, providing an effective operating range of up to 20 meters (approximately 65 feet) in open space. Performance may vary depending on environmental factors such as obstacles, walls, and other wireless interference.

Image: A hand holding the compact SilverStone ES02-USB wireless remote control, demonstrating its ergonomic design.

Manteniment

The SilverStone ES02-USB requires minimal maintenance. The primary maintenance task is battery replacement for the wireless remote control.

Canvi de bateria

The remote control uses one CR2032 coin cell battery. When the remote's range decreases significantly or it stops responding, it's likely time to replace the battery.

1. Localitzeu el compartiment de la bateria a la part posterior del comandament a distància.
2. Use a small screwdriver or coin to open the compartment cover.
3. Traieu la bateria CR2032 antiga.
4. Inseriu una nova bateria CR2032 amb el costat positiu (+) cap amunt.
5. Col·loqueu la coberta del compartiment de manera segura.

Nota: Desfeu-vos de les piles velles de manera responsable d'acord amb la normativa local.

Resolució de problemes

If you encounter issues with your ES02-USB, refer to the following common problems and solutions:

• El comandament a distància no respon:
  • Check the battery in the remote control. Replace it if necessary.
  • Ensure the ES02-USB receiver board is securely connected to the motherboard's USB 2.0 9-pin header.
  • Verify that the Power SW and Reset SW cables are correctly connected to both the Y-cable and the motherboard.
  • Ensure the computer is powered on and the motherboard is receiving power.
• Rang de funcionament reduït:
  • Substituïu la bateria del comandament a distància.
  • Ensure there are no significant physical obstructions (e.g., thick walls, metal objects) between the remote and the computer.
  • Minimitzar les interferències d'altres dispositius sense fil de 2.4 GHz (per exemple, encaminadors Wi-Fi, telèfons sense fil).
• Computer case buttons not working:
  • Double-check the connections of your computer case's Power SW and Reset SW cables to the ES02-USB Y-cable.
  • Ensure the Y-cable is correctly connected to the motherboard's front panel headers.

Especificacions

Garantia i Suport

For warranty information and technical support, please visit the official SilverStone Technology weblloc web o poseu-vos en contacte amb el servei d'atenció al client. Conserveu el rebut de compra per a reclamacions de garantia.

Official SilverStone Weblloc: www.silverstonetek.com