Introducció
This manual provides instructions for the Viper 7146V 1-Way 4-Button Remote Control. This remote serves as an additional or replacement unit for compatible Viper security and remote start systems. It offers a range of up to 1/4 mile for convenient vehicle operation.
Producte acabatview
Figura 1: Davant view of the Viper 7146V remote control. Features four buttons: Lock, Unlock, Remote Start, and Auxiliary. A blue LED indicator is visible above the buttons.
Figura 2: Enrere view of the Viper 7146V remote control. Displays the model number and compliance information on a sticker.
The Viper 7146V remote features a compact, ergonomic design with four distinct buttons for primary functions. It includes a small LED indicator for status feedback.
Configuració
Instal·lació de la bateria
The Viper 7146V remote control uses one CR2 battery (included). To install or replace the battery:
- Locate the small notch or seam on the side of the remote casing.
- Obriu amb cura el comandament a distància casing using a small, flat tool (e.g., a small screwdriver or guitar pick).
- Remove the old battery, noting its polarity (+/-).
- Insert the new CR2 battery, ensuring correct polarity.
- Align the two halves of the remote casing and press firmly until they snap securely into place.
System Pairing (Programming)
The 7146V remote must be programmed to your vehicle's Viper security and remote start system. The programming procedure varies depending on the specific Viper system installed in your vehicle. Refer to your vehicle's Viper system installation manual or consult a professional installer for detailed programming instructions. Compatible systems include, but are not limited to: 4105V, 5305V, 3305V, 5105V, 3102V, 3305V, 3105V.
Nota: Incorrect programming can lead to system malfunction. If you are unsure about the programming steps, it is highly recommended to seek assistance from a certified Viper installer.
Instruccions de funcionament
The Viper 7146V remote provides four primary functions:
- Botó de bloqueig (🔒): Press this button once to lock your vehicle's doors and arm the security system. The vehicle's lights may flash and/or the horn may chirp to confirm the action.
- Botó de desbloqueig (🔓): Press this button once to unlock your vehicle's doors and disarm the security system. The vehicle's lights may flash and/or the horn may chirp to confirm the action.
- Remote Start Button (↻): Press and hold this button for approximately 2-3 seconds to remotely start your vehicle. The vehicle's lights will typically flash to indicate the remote start sequence has begun. The engine will start after a short delay. Press and hold again to turn off the engine.
- Auxiliary Button (S): This button is typically used for additional functions, such as trunk release, power sliding doors, or other custom features, depending on your Viper system's configuration. Refer to your main Viper system manual for specific auxiliary function details.
The remote has an operating range of up to 1/4 mile, though actual range may vary based on environmental factors, vehicle interference, and battery strength.
Manteniment
Canvi de bateria
When the remote's range decreases significantly or the LED indicator becomes dim or unresponsive, it is likely time to replace the battery. Follow the "Battery Installation" steps in the Setup section. Use a fresh CR2 battery for optimal performance.
Neteja
To clean the remote, use a soft, dry cloth. Do not use abrasive cleaners, solvents, or immerse the remote in water, as this can damage the internal electronics.
Resolució de problemes
| Problema | Causa possible | Solució |
|---|---|---|
| El comandament a distància no respon. | Dead or low battery. Remote is out of range. Remote is not programmed to the system. | Replace the battery. Move closer to the vehicle. Re-program the remote (refer to System Pairing). |
| Rang de funcionament reduït. | Low battery. Environmental interference (e.g., large buildings, radio towers). | Replace the battery. Try operating the remote in a different location. |
| El vehicle no arrenca a distància. | Vehicle conditions not met (e.g., hood open, door ajar, manual transmission not in neutral safety). System error. | Ensure all vehicle conditions are met. Consult your main Viper system manual or a professional installer. |
Especificacions
- Model: 7146 V
- Tipus: Control remot unidireccional de 4 botons
- Interval de funcionament: Up to 1/4 mile (approx. 400 meters)
- Bateria: 1 x CR2 (inclòs)
- Dimensions: 8 x 4 x 0.5 polzades (aproximadament)
- Pes: 0.64 unces (aproximadament)
- Característiques especials: Disseny ergonòmic
- Compatible Viper Systems: 4105 V, 5305 V, 3305 V, 5105 V, 3102 V, 3305 V, 3105 V
Garantia i Suport
For warranty information and technical support regarding your Viper 7146V remote control or your Viper security and remote start system, please refer to the documentation provided with your complete system or visit the official Viper website. It is recommended to contact a professional Viper installer for any complex issues or system modifications.
Recursos en línia: Per obtenir més assistència i informació sobre el producte, podeu visitar la Botiga Viper a Amazon.
