Manual d'instruccions de la font d'alimentació Keithley 2303-PJ
Model: 2303-PJ
1. Producte acabatview
The Keithley 2303-PJ is a specialized power supply designed for testing portable, battery-operated devices. It offers advanced capabilities to simulate a battery's performance across a wide range of conditions, including output resistance and voltage response. This instrument is crucial for accurately testing device charge control circuitry and overall battery simulation.
Les característiques clau inclouen:
- Ultra-fast response to transient load currents
- Variable output resistance
- 100nA DC current sensitivity
Figure 1: Front panel of the Keithley 2303-PJ Power Supply. The display shows voltage and current readings (e.g., 3.60V, 1.08A). Controls include a navigation pad, 'DISPLAY', 'MENU', 'OPERATE', 'ENTER', 'SET' buttons, and a 'POWER' button with indicator lights.
2. Configuració
- Desembalatge i inspecció: Carefully remove the instrument from its packaging. Inspect for any signs of damage during transit. Report any damage to the shipping carrier and Keithley immediately.
- Connexió d'alimentació: Connect the supplied AC power cord to the instrument's rear panel power inlet and then to a grounded AC power outlet. Ensure the power source matches the instrument's voltage requisits.
- Encesa inicial: Premeu el botó PODER button located on the front panel. The display should illuminate, indicating the unit is operational.
- Connecting to Device Under Test (DUT): Use appropriate test leads to connect the output terminals of the 2303-PJ to the device you intend to test. Observe correct polarity.
- Ventilació: Ensure adequate ventilation around the instrument. Do not block the ventilation grilles on the sides or rear of the unit.
3. Instruccions de funcionament
3.1 Controls del panell frontal
- Visualització: Mostra el volum de sortidatage, current, and other operational parameters.
- Botons de navegació (amunt, avall, esquerra, dreta): Used to navigate through menus and adjust parameter values.
- Botó ENTER: Confirms selections or entered values.
- Botó SET: Entra al mode de configuració de paràmetres.
- Botó MENÚ: Accesses the main menu for configuration and advanced settings.
- OPERATE Button: Toggles the output on or off.
- Botó DISPLAY: Cycles through different display modes or views.
3.2 Funcionament bàsic
- Configuració Voltage i actual:
- Premeu el botó SET botó.
- Use the navigation buttons to select the voltage or current parameter you wish to adjust.
- Use the navigation buttons (typically Up/Down) to change the value.
- Premeu ENTRAR per confirmar la configuració.
- Habilitació de la sortida:
- Once parameters are set, press the OPERAR button to enable the power output. The output indicator should illuminate.
- To disable the output, press OPERAR de nou.
- Lectures de seguiment:
The display continuously shows the actual output voltage and current. Use the VISUALITZACIÓ button to cycle through different measurement views si està disponible.
4. Manteniment
- Neteja: Keep the instrument clean by wiping the exterior with a soft, damp cloth. Do not use abrasive cleaners or solvents. Ensure the unit is powered off and disconnected from the AC supply before cleaning.
- Ventilació: Periodically check that the ventilation grilles are free from dust and debris to ensure proper airflow and prevent overheating.
- Emmagatzematge: When not in use for extended periods, store the instrument in a clean, dry environment within its specified operating temperature and humidity ranges.
- Calibració: For optimal performance and accuracy, periodic calibration by qualified personnel is recommended. Refer to the Keithley service manual or contact Keithley support for calibration procedures and intervals.
5. Solució De Problemes
| Problema | Causa possible | Solució |
|---|---|---|
| L'instrument no s'encén. | No AC power; faulty power cord; internal fuse blown. | Check AC power connection and outlet. Try a different power cord. If fuse is suspected, contact qualified service personnel. |
| Sense sortida voltage / actual. | Output disabled; incorrect settings; overload protection active; faulty connections. | Premeu OPERAR to enable output. Verify voltage/current settings. Check for short circuits or overloads on the DUT. Ensure test leads are securely connected. |
| Lectures inestables o inexactes. | Poor connections; external interference; instrument needs calibration. | Check all connections for looseness or corrosion. Ensure the instrument is away from strong electromagnetic fields. Consider professional calibration. |
| Sobreescalfament. | Blocked ventilation; excessive ambient temperature; continuous operation at maximum load. | Ensure ventilation grilles are clear. Operate in a cooler environment. Reduce load or allow for cool-down periods. |
For issues not listed here or if troubleshooting steps do not resolve the problem, please contact Keithley technical support.
6. Especificacions
| Paràmetre | Valor |
|---|---|
| Fabricant | Keithley |
| Número de part | 2303-PJ |
| Número de model de l'article | 2303-PJ |
| Pes de l'article | 5.44 kg |
| Dimensions del paquet | 48.26 x 33.02 x 22.86 cm |
| Quantitat de paquet d'articles | 1 |
| Necessites piles? | No |
| Data de primera disponibilitat | 4 de novembre de 2016 |
7. Garantia i Suport
Warranty information for the Keithley 2303-PJ Power Supply is typically provided with the product at the time of purchase or can be found on the official Keithley weblloc web. Si us plau, conserveu el comprovant de compra per a reclamacions de garantia.
For technical support, service, or calibration inquiries, please contact Keithley customer service directly. Refer to the contact information provided in your product documentation or on the official Keithley weblloc (www.tek.com/keithley).
