Introducció
This manual provides comprehensive instructions for the safe and proper installation, operation, and maintenance of your Mount-It! Dual LCD Monitor Wall Mount, model MI-35114. This wall mount is designed to securely hold two LCD monitors, offering adjustable viewing angles and saving valuable desk space. Please read this manual thoroughly before beginning installation to ensure correct setup and to prevent damage or injury.
Informació de seguretat
ADVERTIMENT: Failure to read, understand, and follow all instructions contained herein may result in serious personal injury, property damage, or voiding of your warranty. If you have any questions regarding these instructions, please contact Mount-It! customer support.
- Do not exceed the maximum weight capacity of the mount. Refer to the Specifications section for details.
- Ensure the mounting surface (wall) can safely support the combined weight of the mount and the monitors.
- Always use a stud finder to locate wall studs for secure mounting. If mounting to concrete or brick, use appropriate anchors (not always included).
- Do not overtighten screws. Overtightening can cause damage to the product or the mounting surface.
- Mantingueu totes les peces petites i els materials d'embalatge fora de l'abast dels nens.
- If any parts are missing or defective, do not attempt to install. Contact customer service for replacement parts.
- Professional installation is recommended if you are unsure about the installation process.
Contingut del paquet
Please verify that all components are present and in good condition before beginning installation.
- Muntatge de paret (braç principal i placa de paret)
- VESA Monitor Plates (x2)
- Hardware Kit (various screws, washers, spacers for wall and monitor attachment)
- Manual d'instruccions (aquest document)
Configuració i instal·lació
Follow these steps carefully to install your monitor wall mount.
Eines necessàries (no incloses):
- Tornavís Phillips
- Trepant
- Drill Bit (appropriate size for wall anchors/lag bolts)
- Cercador de perns
- Nivell
- Llapis
- Cinta mètrica
Instal·lació pas a pas:
- Prepara el mur:
Use a stud finder to locate a suitable wooden stud in your wall. Mark the center of the stud at your desired mounting height. Ensure there are no electrical wires or plumbing in the drilling path.
- Fixeu la placa de paret:
Position the wall plate of the mount against the marked stud. Use a level to ensure it is perfectly horizontal. Mark the drill hole locations with a pencil. Drill pilot holes into the stud. Secure the wall plate to the wall using the provided lag bolts and washers. Do not overtighten.
Image: The Mount-It! MI-35114 dual monitor wall mount, illustrating its articulated arm and VESA mounting plate. This image shows the overall structure of the mount, which attaches to the wall and supports monitors.
- Fixeu les plaques VESA als monitors:
Carefully place your monitor face down on a soft, clean surface. Align the VESA plate (the square bracket with holes) with the mounting holes on the back of your monitor. Use the appropriate screws and washers from the hardware kit to secure the VESA plate to the monitor. Ensure the screws are not too long, which could damage the monitor's internal components. Repeat for the second monitor.
- Mount Monitors to Arm:
With assistance, carefully lift each monitor (with its attached VESA plate) and slide it onto the corresponding arm of the wall mount. Ensure the VESA plate securely locks into place on the arm. Some mounts may have a locking screw to further secure the monitor; tighten if applicable.
- Ajustaments inicials:
Once both monitors are mounted, make initial adjustments to tilt, swivel, and rotation to achieve a comfortable viewing position. Refer to the Operating Instructions section for detailed adjustment guidance.
Instruccions de funcionament
Your Mount-It! wall mount offers various adjustment capabilities for optimal viewcomoditat.
- Ajust d'alçada: The arm allows for vertical positioning. Gently lift or lower the monitor to your desired height. Some models may require adjusting a tension screw to hold the position.
- Ajust d'inclinació: To change the vertical angle of your monitor, grasp the top and bottom edges of the monitor and gently tilt it forwards or backwards.
- Ajust de gir: To rotate the monitor horizontally, gently push the monitor left or right. The arm allows for a wide range of swivel motion.
- Rotació (Retrat/Paisatge): The VESA plate allows for 360-degree rotation, enabling you to switch your monitor between landscape and portrait orientations. Gently rotate the monitor until it clicks into the desired position.
- Gestió de cables: Utilize the integrated cable clips or channels on the arm to route and conceal your monitor cables for a clean and organized setup.
Manteniment
Regular maintenance will ensure the longevity and safe operation of your monitor mount.
- Neteja: Utilitzeu un suau, damp cloth to wipe down the mount. Avoid abrasive cleaners or solvents that could damage the finish.
- Comprovacions periòdiques: Every few months, check all screws and bolts to ensure they are still tight and secure. Retighten if necessary, but do not overtighten.
- Lubricació: The moving parts of the mount are designed for smooth operation and generally do not require lubrication. If you notice any stiffness, contact customer support.
Resolució de problemes
If you encounter any issues during installation or operation, refer to the following common problems and solutions.
| Problema | Causa possible | Solució |
|---|---|---|
| El monitor s'enfonsa o no manté la posició. | Tension screws are too loose; monitor weight exceeds capacity. | Tighten the tension adjustment screws on the arm joints. Verify monitor weight is within specified limits. |
| Mount feels unstable on the wall. | Wall plate not securely fastened; incorrect wall type. | Ensure lag bolts are fully tightened into a wall stud. If not mounted to a stud, re-install into a stud or use appropriate heavy-duty anchors for your wall type. |
| Difficulty attaching VESA plate to monitor. | Incorrect screw size; VESA holes not aligned. | Use the correct diameter and length screws from the hardware kit. Ensure the VESA plate is perfectly aligned with the monitor's mounting holes. |
If the problem persists, please contact Mount-It! customer support for further assistance.
Especificacions
| Característica | Detall |
|---|---|
| Número de model | MI-35114 |
| Tipus de muntatge | Muntatge de paret |
| Mides de monitor compatibles | De 13 a 27 polzades |
| Compatibilitat VESA | 75x75mm, 100x100mm |
| Nombre de monitors compatibles | 2 (dual) |
| Color | Plata |
| Ajustaments | Height, Tilt, Swivel, Rotation |
Garantia i Suport
Specific warranty information for the Mount-It! MI-35114 Dual LCD Monitor Wall Mount is not provided in this document. Please refer to the official Mount-It! weblloc web o la documentació de compra per obtenir els termes i condicions detallats de la garantia.
For technical support, missing parts, or any other inquiries, please visit the Mount-It! support page or contact their customer service directly. Contact information can typically be found on the manufacturer's official weblloc.
