Manual d'usuari del mòdul de xarxa Cisco Catalyst 9300 8 x 10GE

1. Introducció

This manual provides comprehensive instructions for the installation, operation, and maintenance of the Cisco Catalyst 9300 8 x 10GE Network Module (C9300-NM-8X=). This module is designed to expand the networking capabilities of compatible Cisco Catalyst 9300 series switches, offering high-speed 10 Gigabit Ethernet connectivity.

The C9300-NM-8X= is a spare network module, providing 8 x 10GE ports for data networking applications. It supports twisted pair media and utilizes 10 Gigabit Ethernet technology with 10GBase-X network technology.

2. Producte acabatview

The Cisco Catalyst 9300 8 x 10GE Network Module is a critical component for enhancing network performance and scalability. Below is an image of the module, highlighting its physical characteristics.

Figura 2.1: Cisco Catalyst 9300 8 x 10GE Network Module. This image shows the network module with its 8 x 10GE ports and the integrated handle for insertion and removal. The module features a green circuit board and a silver-colored metal housing for the ports.

Característiques principals:

• Application/Usage: Data Networking
• Interfaces/Ports Details: 8 x 10GBase-X network ports
• Tipus de suport compatible: Parell trenat
• Ethernet Technology: 10 Gigabit Ethernet
• Tecnologia de xarxa: 10 GBase-X

3. Configuració i instal·lació

Before installing the network module, ensure the host Cisco Catalyst 9300 series switch is powered off and disconnected from its power source to prevent electrical shock or damage to the equipment.

3.1 Precaucions de seguretat

• Always wear an anti-static wrist strap when handling the module to prevent electrostatic discharge (ESD) damage.
• Ensure the installation environment is clean and free of dust.
• Do not force the module into the slot; if it does not slide in easily, recheck its orientation.

3.2 Passos d'instal·lació

1. Locate an available network module slot on your Cisco Catalyst 9300 series switch.
2. Carefully align the network module with the slot. The module is keyed to fit in only one orientation.
3. Gently slide the module into the slot until it is fully seated. Use the integrated handle for better grip.
4. Secure the module by tightening any captive screws or engaging the ejector levers, if present, to lock it into place.
5. Once installed, reconnect the switch to its power source and power it on.
6. Verify the module's status indicators (LEDs) to ensure it is properly recognized and operational. Refer to the switch's documentation for LED interpretations.

4. Operating the Network Module

After successful installation, the network module becomes an integral part of your Cisco Catalyst 9300 switch. Configuration and management of the 10GE ports are performed through the switch's operating system (Cisco IOS XE).

4.1 Connexió de dispositius

• Connect 10 Gigabit Ethernet compatible devices (e.g., servers, other switches) to the 8 x 10GE ports using appropriate twisted pair cabling.
• Ensure cables are securely connected to both the module port and the connected device.

4.2 Basic Configuration (via Cisco IOS XE)

Access the switch's command-line interface (CLI) to configure the network module's ports. Common tasks include:

• Configuració de la interfície: Assigning IP addresses, configuring VLANs, and setting port modes.
• Speed and Duplex Settings: While 10GE ports typically operate at fixed speeds, verify settings if issues arise.
• Link Aggregation (EtherChannel): Grouping multiple 10GE ports for increased bandwidth and redundancy.

Refer to the Cisco Catalyst 9300 Series Switch Software Configuration Guide for detailed command syntax and advanced configurations.

5. Manteniment

Regular maintenance ensures the longevity and optimal performance of your network module.

5.1 Neteja

• Periodically inspect the module's ports for dust accumulation.
• Use a can of compressed air to gently remove dust from the ports and surrounding areas.
• Do not use liquid cleaners directly on the module.

5.2 actualitzacions de microprogramari

Firmware updates for the network module are typically part of the Cisco IOS XE software updates for the host switch. Always consult Cisco's official documentation and release notes before performing any software upgrades.

5.3 Module Removal

To remove the module:

1. Power off the host switch and disconnect its power source.
2. Disconnect all cables from the network module ports.
3. Unscrew any captive screws or disengage ejector levers securing the module.
4. Gently pull the module straight out of the slot using the integrated handle.
5. Store the module in an anti-static bag if not immediately reinstalling.

6. Solució De Problemes

Aquesta secció proporciona els passos bàsics per a la resolució de problemes comuns.

For more advanced troubleshooting, consult the Cisco Catalyst 9300 Series Switch Troubleshooting Guide or contact Cisco Technical Assistance Center (TAC).

7. Especificacions

Detailed technical specifications for the Cisco Catalyst 9300 8 x 10GE Network Module (C9300-NM-8X=).

8. Garantia i Suport

For information regarding product warranty, please refer to the official Cisco warranty statement provided with your purchase or visit the Cisco website. Warranty terms may vary based on region and purchase agreement.

8.1 Suport tècnic

For technical assistance, product documentation, and software downloads, please visit the official Cisco Support weblloc:

Suport de Cisco

You may also contact Cisco Technical Assistance Center (TAC) for direct support, details of which can be found on the Cisco Support weblloc.