Introducció
Welcome to the user manual for the Connects2 CTSNS017.2 Steering Wheel Control Interface. This device is designed to allow you to retain the original steering wheel audio controls when upgrading your vehicle's head unit.
Per a un rendiment i una seguretat òptims, llegiu atentament aquestes instruccions abans de la instal·lació i l'ús.
Producte acabatview
The Connects2 CTSNS017.2 is an automotive interface that integrates with your vehicle's existing wiring to provide seamless control of your aftermarket car stereo via the steering wheel buttons. It features OEM-specific connectors for a direct fit.
Components del producte
Image: The Connects2 CTSNS017.2 interface module (black box on the right) connected to various multi-pin wiring harnesses. The harnesses include white and black connectors designed to integrate with vehicle-specific wiring.
Compatibilitat
This interface is specifically designed for select Nissan vehicles. Please verify your vehicle's make, model, and year against the list below to ensure compatibility.
- Nissan X-Trail (2001-2008)
- Nissan Almera (2000-2006)
- Nissan Primera (2001-2007)
- Nissan Terrano (2001-2006)
Important: Always refer to the official Connects2 compatibility guide or consult with a professional installer to confirm correct compatibility and installation for your specific vehicle model and aftermarket head unit.
Configuració i instal·lació
Installation of the CTSNS017.2 requires technical knowledge of car audio wiring and vehicle electronics. It is highly recommended that installation be performed by a qualified professional.
Abans de començar
- Assegureu-vos que el vehicle estigui apagat i que el terminal negatiu de la bateria estigui desconnectat per evitar curtcircuits.
- Gather necessary tools (e.g., wire strippers, crimpers, electrical tape, trim removal tools).
- Identify the vehicle's original head unit wiring harness and the aftermarket head unit's wiring harness.
Passos d'instal·lació (Guia general)
- Remove the original factory head unit from the dashboard.
- Locate the vehicle's original wiring harness.
- Connect the OEM-specific connectors of the CTSNS017.2 interface to the corresponding vehicle wiring harness. These connectors are designed for a direct fit.
- Connect the other end of the CTSNS017.2 interface (typically a multi-pin connector or flying leads) to the aftermarket head unit's steering wheel control input (often labeled "SWC," "Key1," "Key2," or "Remote In"). Refer to your aftermarket head unit's manual for specific wiring instructions.
- Assegureu-vos que totes les connexions estiguin segures i aïllades correctament.
- Torneu a connectar la bateria del vehicle.
- Test the steering wheel controls with the new head unit. If controls are not functioning, refer to the troubleshooting section or the aftermarket head unit's manual for programming instructions.
- Carefully reassemble the dashboard, ensuring no wires are pinched.
Warning: Incorrect installation can lead to damage to the interface, head unit, or vehicle's electrical system. If you are unsure, seek professional assistance.
Instruccions de funcionament
Once correctly installed and configured, the Connects2 CTSNS017.2 interface operates automatically. Your vehicle's original steering wheel audio controls will now send signals to your aftermarket head unit, allowing you to control functions such as:
- Pujar/Bajar el volum
- Track/Station Next/Previous
- Selecció de mode/font
- Silenciar
The specific functions supported may vary depending on your vehicle's original steering wheel controls and the aftermarket head unit's capabilities. Some aftermarket head units may require initial programming or learning of the steering wheel controls; refer to your head unit's manual for details.
Manteniment
The Connects2 CTSNS017.2 interface is a sealed electronic component and requires no routine maintenance. Keep the unit free from moisture and extreme temperatures. Do not attempt to open or repair the unit, as this will void any warranty.
Resolució de problemes
Si teniu problemes després de la instal·lació, tingueu en compte els passos següents per resoldre'ls:
- No Steering Wheel Control Functionality:
- Verify all connections are secure and correctly wired according to the installation instructions and your aftermarket head unit's manual.
- Ensure the aftermarket head unit's steering wheel control input is correctly connected to the interface.
- Check if your aftermarket head unit requires programming or "learning" of the steering wheel controls. Consult its manual.
- Confirm vehicle compatibility with the CTSNS017.2.
- Intermittent Control:
- Comproveu si hi ha connexions soltes o corroïdes.
- Ensure proper grounding of the head unit and interface.
- Incorrect Button Function:
- This often indicates a need for programming or re-programming the steering wheel controls within your aftermarket head unit's settings.
If problems persist, contact Connects2 customer support or a professional car audio installer.
Especificacions
| Característica | Detall |
|---|---|
| Número de model | CTSNS017.2 |
| Marca | Connecta2 |
| Tipus de producte | Interfície de control del volant |
| Tipus de connector | OEM Specific |
| Pes | 100 g |
| Dimensions (L x A x A) | 30 x 25 x 5 cm |
Garantia i Suport
For warranty information, please refer to the documentation provided with your purchase or visit the official Connects2 website. Connects2 is a leading brand in automotive accessories, known for designing specific interface solutions for major market brands since 1999.
For technical support or further assistance, it is recommended to visit the official Connects2 source to confirm compatibility and correct installation procedures.
