DROK DC-DC Buck Converter Module Instruction Manual

1. Introducció

This manual provides detailed instructions for the DROK DC-DC Buck Converter Module. This module is a highly efficient, compact step-down voltage regulator designed to convert a higher DC input voltage to a lower, stable DC output voltage. It offers both adjustable and selectable fixed output voltage options, making it versatile for various electronic projects and applications.

Les característiques principals inclouen un ampli volum d'entradatage range, high conversion efficiency, ultra-small size, low ripple, and stable performance. The robust construction incorporates an imported potentiometer, a 3A current chip, a high-current shielded inductor, and long-life solid capacitors (MLCC).

Figura 1: Mésview of five DROK DC-DC Buck Converter Modules.

2. Especificacions

Figure 2: Module dimensions for integration.

3. Configuració i instal·lació

3.1 Mòdul acabatview i connexions

The module features clearly marked terminals for input, output, ground, and an enable pin. The potentiometer allows for adjustable output voltage.

Figura 3: superior view of the module with connection points and potentiometer.

• IN+: Positive input voltage (DC 4.5V-24V)
• GND: Common ground for input and output
• VOUT+: Positive output voltage
• EN: Enable pin (default active, low level turns off)
• Potenciòmetre: For adjusting output voltage when not using fixed output.

3.2 Setting Output Voltage

The module supports two modes for output voltage: adjustable and fixed. By default, the module is in adjustable mode, controlled by the onboard potentiometer.

Vol. de sortida ajustabletage:

To set an adjustable output voltage between 0.8V and 17V, connect your input power to IN+ and GND. Then, use a small screwdriver to turn the onboard potentiometer (located on the top left of the module, as shown in Figure 3) clockwise to increase the voltage or counter-clockwise to decrease it. Monitor the output voltage with a multimeter connected to VOUT+ and GND.

Vol de sortida fixatage:

For specific fixed output voltages (1.8V, 2.5V, 3.3V, 5V, 9V, 12V), the module provides solder pads on the backside. To select a fixed voltage, you must first cut the trace to the 'ADJ' pad and then solder the desired voltage pad to the adjacent common pad. This disables the potentiometer for fixed output operation.

Figura 4: A baix view of the module with fixed voltage selection pads.

Procedure for Fixed Voltage Selecció:

1. Desconnecteu l'alimentació: Ensure the module is completely disconnected from any power source before proceeding.
2. Cut ADJ Trace: Locate the 'ADJ' pad on the backside of the module (top left, as shown in Figure 4). Carefully cut the trace connecting the 'ADJ' pad to the main circuit. This disables the adjustable function.
3. Solder Desired Voltage Pad: Identify the solder pad corresponding to your desired fixed output voltage (e.g., 5V). Solder this pad to its adjacent common pad.

Figura 5: Example of setting fixed 5V output by cutting the ADJ trace and soldering the 5V pad.

Figura 6: Detallada view of the soldered 5V pad after cutting the ADJ trace.

Nota: Some users have reported that the silk screen labels for fixed voltage pads might be offset. Always verify the output voltage with a multimeter after soldering to ensure the correct voltage is achieved. If the initial fixed voltage is not as expected, you may need to adjust the potentiometer slightly after selecting a fixed output, or re-evaluate the soldering points.

4. Instruccions de funcionament

Un cop la sortida desitjada voltage is set (either adjustable or fixed), connect your load to the VOUT+ and GND terminals. Ensure that the input voltage is within the specified range (DC 4.5V-24V) and that the output current does not exceed 3A.

• Enable Pin (EN): The integrated enable port is set to operate by default. When the electrical level is low, the module will turn off. This feature can be used for external control of the module's operation.
• Refrigeració: For output currents approaching the maximum 3A, it is recommended to enhance cooling. This may involve adding a heatsink or ensuring adequate airflow around the module to prevent overheating and maintain stable performance.

5. Manteniment

The DROK DC-DC Buck Converter Module is designed for reliable operation with minimal maintenance. Follow these guidelines to ensure longevity:

• Mantenir net: Periodically inspect the module for dust or debris accumulation. Clean gently with a soft, dry brush if necessary.
• Eviteu la humitat: Protect the module from moisture and corrosive environments.
• Ventilació: Ensure proper ventilation, especially when operating at higher loads, to dissipate heat effectively.
• Connexions segures: Regularly check all input and output connections to ensure they are secure and free from shorts.

6. Solució De Problemes

If you encounter issues with your DROK DC-DC Buck Converter Module, consider the following troubleshooting steps:

• Sense Vol de sortidatage:
  • Verifiqueu el volum d'entradatage is present and within the 4.5V-24V range.
  • Comproveu totes les connexions del cablejat per assegurar-vos que la polaritat sigui correcta i que el contacte sigui segur.
  • Ensure the EN pin is not pulled low, which would disable the module.
• Volum de sortida incorrectetage:
  • Adjustable Mode: If using the potentiometer, ensure it is properly adjusted. Turn it slowly and check with a multimeter.
  • Mode fix: If fixed voltage is selected, verify that the ADJ trace was correctly cut and the desired voltage pad was properly soldered. Due to potential silk screen offsets, always confirm the output with a multimeter. Re-check soldering if necessary.
  • Assegureu-vos que l'entrada voltage is sufficiently higher than the desired output voltage (at least 1.5V-2V difference for stable buck conversion).
• Sobreescalfament del mòdul:
  • Reduce the output current if it exceeds 1.5A without additional cooling.
  • Ensure adequate ventilation around the module. Consider adding a small heatsink for continuous high-current operation.
• Sortida inestable:
  • Comproveu si hi ha connexions soltes o curtcircuits intermitents.
  • Ensure the load is not exceeding the module's current capacity.
  • Verify the input power supply is stable and capable of providing sufficient current.

7. Garantia i Suport

For warranty information or technical support, please refer to the product listing on the retailer's weblloc web o contacteu directament amb el venedor. Conserveu el rebut de compra com a comprovant de compra.