1. Producte acabatview
The Red Lion Controls PAXCDS20 is a Quad Setpoint Relay Output Card designed to expand the functionality of Red Lion PAX Series Meters. This card provides four independent relay outputs, enabling the meter to control external devices or trigger alarms based on configured setpoints. It integrates seamlessly with compatible PAX meters, offering enhanced control capabilities for various industrial applications.
Image 1.1: The Red Lion Controls PAXCDS20 Pax Quad Setpoint Relay Output Card. This image displays the green circuit board with black relay components and a terminal block for connections.
2. Instal·lació i configuració
Proper installation is crucial for the reliable operation of the PAXCDS20 card. Ensure all power is disconnected from the PAX meter before proceeding with installation.
2.1 Instal·lació física
- Desconnexió d'alimentació: Turn off and disconnect all power to the PAX Series Meter.
- Ranura d'accés: Locate the expansion slot on the rear or side of the PAX meter, as specified in the meter's primary manual.
- Insereix la targeta: Carefully align the PAXCDS20 card with the expansion slot connector. Gently push the card into the slot until it is fully seated. Avoid excessive force.
- Targeta segura: If applicable, use any provided screws or clips to secure the card in place within the meter housing.
2.2 Connexions elèctriques
The PAXCDS20 card provides four relay outputs. Refer to the wiring diagram in the PAX meter's main manual for specific terminal assignments.
- Sortides de relé: Connect external devices (e.g., alarms, contactors, solenoids) to the appropriate relay output terminals. Ensure that the voltage and current ratings of the connected devices do not exceed the specifications of the PAXCDS20 relays.
- Wiring Practices: Use appropriate wire gauges and follow all local electrical codes and safety regulations.
3. Funcionament
Once installed, the PAXCDS20 card's relay outputs are controlled by the setpoint configurations within the host PAX Series Meter. The card itself does not have user-configurable settings; all control is managed through the meter's programming.
3.1 Setpoint Configuration
Refer to the Red Lion PAX Series Meter's primary instruction manual for detailed instructions on configuring setpoints. This typically involves:
- Accessing the meter's programming menu.
- Defining the setpoint values (e.g., high limit, low limit).
- Assigning each setpoint to a specific relay output on the PAXCDS20 card.
- Configuring the relay action (e.g., normally open/closed, latching/non-latching, delay times).
3.2 Relay Output Functionality
When a configured setpoint condition is met by the PAX meter's input, the corresponding relay on the PAXCDS20 card will activate or deactivate according to its programmed logic. This action can then control the connected external device.
4. Manteniment
The PAXCDS20 card is designed for long-term, reliable operation with minimal maintenance. However, periodic inspection can help ensure continued performance.
- Inspecció visual: Periodically inspect the card and its connections for any signs of damage, corrosion, or loose wiring.
- Neteja: If necessary, gently clean the card using a soft, dry brush or compressed air to remove dust and debris. Do not use liquid cleaners or solvents.
- Condicions ambientals: Assegureu-vos que l'entorn operatiu es mantingui dins dels rangs de temperatura i humitat especificats per evitar fallades prematures dels components.
5. Solució De Problemes
If you encounter issues with the PAXCDS20 card, consider the following troubleshooting steps:
| Problema | Possible solució |
|---|---|
| Relay outputs not activating |
|
| Intermittent relay operation |
|
| Card not recognized by PAX meter |
|
If problems persist after attempting these solutions, contact Red Lion Controls technical support.
6. Especificacions tècniques
- Fabricant: Controls Red Lion
- Model: PAXCDS20
- Tipus de producte: Quad Setpoint Relay Output Card
- Compatibilitat: Red Lion PAX Series Meters
- Sortides: 4 Form C (SPDT) Relays
- Valoració del relé: (Refer to the specific PAX meter manual or Red Lion Controls datasheet for detailed current/voltage ratings)
- Instal·lació: Plug-in expansion card
- Data de primera disponibilitat: 7 de maig de 2018
7. Garantia i Suport
Red Lion Controls products are manufactured to high standards and are typically covered by a limited warranty against defects in materials and workmanship. For specific warranty terms and conditions applicable to the PAXCDS20, please refer to the official Red Lion Controls website or the documentation included with your PAX Series Meter.
For technical assistance, product support, or to report issues, please contact Red Lion Controls customer service or visit their official support portal. Provide your product model number (PAXCDS20) and any relevant details about your system when seeking support.
