AVANTEK CW-11 Wireless Doorbell Instruction Manual

1. Introducció

Thank you for choosing the AVANTEK CW-11 Wireless Doorbell. This manual provides essential information for the proper installation, operation, and maintenance of your new doorbell system. Please read these instructions carefully before use and retain them for future reference.

Image 1.1: AVANTEK CW-11 Wireless Doorbell system, showing the compact transmitter and receiver units.

2. Informació de seguretat

• No exposeu el dispositiu a temperatures extremes ni a la llum solar directa.
• Keep the device away from water and high humidity. The transmitter is IP55 waterproof, but the receiver is for indoor use only.
• No intenteu desmuntar o reparar el dispositiu vosaltres mateixos. Contacteu amb l'assistència al client per obtenir assistència.
• Mantingueu les piles fora de l'abast dels nens. Desfeu-vos de les piles usades correctament.

3. Contingut del paquet

• 1 x Wireless Transmitter (Doorbell Button)
• 1 x Plug-in Receiver (Chime Unit)
• 1 x CR2 Battery (pre-installed in transmitter)
• 2 x cargols
• 2 x ancoratges
• 1 x cinta adhesiva de doble cara
• 1 x tornavís

4. Producte acabatview

The AVANTEK CW-11 Wireless Doorbell system consists of a battery-powered transmitter (doorbell button) and a plug-in receiver (chime unit). The receiver features 52 selectable melodies, 5 adjustable volume levels, and an LED indicator for visual alerts.

Image 4.1: The receiver unit, illustrating its features including 52 chimes, 5 volume levels, and an LED indicator.

Image 4.2: The compact size of both the transmitter and receiver, designed to not obstruct adjacent power sockets.

5. Instruccions de configuració

5.1 Installing the Transmitter

The transmitter can be installed using either the provided double-sided adhesive tape or screws and anchor plugs.

Image 5.1: Visual guide for installing the transmitter using either adhesive tape or screws and anchor plugs.

Method A: Using Double-Sided Adhesive Tape

1. Netegeu a fons la superfície de muntatge desitjada per assegurar-vos que estigui lliure de pols i humitat.
2. Peel off one side of the protective film from the double-sided adhesive tape and attach it to the back of the transmitter.
3. Peel off the other side of the protective film and firmly press the transmitter onto the cleaned surface for at least 30 seconds.

Method B: Using Screws and Anchor Plugs

1. Mark the desired mounting points for the transmitter on the wall.
2. Perfora dos forats a les posicions marcades.
3. Insert the anchor plugs into the drilled holes.
4. Align the transmitter's mounting holes with the anchor plugs and secure it with the provided screws.

Important: To prevent signal interference, do not install the transmitter close to or on metal surfaces such as metal door frames or mailboxes.

5.2 Plugging in the Receiver

Plug the receiver into a standard electrical outlet in a location where the chime can be easily heard. The LED on the receiver will flash upon initial power-up.

5.3 Pairing the Doorbell System

The transmitter and receiver are pre-paired at the factory. If re-pairing is needed or if you add additional transmitters/receivers, follow these steps:

1. Connecteu el receptor a una presa de corrent.
2. To enter pairing mode, hold down the Volume button on the receiver for 3 seconds. The LED on the receiver will flash.
3. Remove the battery insulating film from the transmitter (if not already done).
4. Press the Push button on the transmitter. Its LED will flash.
5. After successful pairing, the receiver will chime once, and the LEDs on both the receiver and transmitter will flash simultaneously.

6. Instruccions de funcionament

6.1 Canvi de melodies

The receiver offers 52 different melodies. Use the 'Next' and 'Previous' buttons on the side of the receiver to cycle through the available tunes. Press the doorbell button to preview the selected melody.

Image 6.1: The receiver offers a wide selection of melodies for personalization.

6.2 Ajust del volum

There are 5 adjustable volume levels, with a maximum setting of 115 dB. Use the 'Volume' button on the side of the receiver to increase or decrease the sound level.

6.3 Mode de silenci

To activate mute mode (0 dB), repeatedly press the 'Volume' button until the sound is off. In this mode, only the LED indicator will flash when the doorbell is pressed, providing a silent visual alert.

Image 6.2: The mute mode feature allows for silent notifications, ideal for quiet environments.

7. Manteniment

7.1 Neteja

Netegeu els dispositius amb un drap suau i sec. No utilitzeu productes de neteja abrasius ni dissolvents.

7.2 Battery Replacement (Transmitter)

The transmitter uses a CR2 battery with an estimated lifespan of 3 years. When the battery is low, the transmitter's LED may not light up or the signal range may decrease. To replace the battery:

1. Obriu amb cura l'emissor casing using the provided screwdriver or a small flat-head screwdriver.
2. Traieu la bateria CR2 antiga.
3. Introduïu una pila CR2 nova, assegurant-vos de la polaritat correcta (+/-).
4. Tanca el casing de manera segura.

8. Solució De Problemes

• Doorbell not chiming: Ensure the receiver is plugged in and powered. Check the transmitter battery. Re-pair the devices if necessary (refer to Section 5.3).
• Short signal range: Ensure the transmitter is not installed on or near metal surfaces. Relocate the receiver to a more central position. Replace the transmitter battery.
• Interferència: The doorbell operates on a frequency that minimizes interference with other household devices. If interference occurs, try changing the melody or relocating the receiver.
• Funció de memòria: The device remembers your last melody and volume level after a power outage, so no need to reset settings.

9. Especificacions

10. Garantia i Suport

For warranty information or technical support, please refer to the contact details provided with your product packaging or visit the official AVANTEK weblloc web. Conserveu el rebut de compra com a comprovant de compra.