1. Introducció
The Ohaus FC5706 Frontier 5000 Series Multi-Function Centrifuge is designed for efficient and reliable separation of various samples in laboratory settings. This manual provides essential information for the safe and effective operation, maintenance, and troubleshooting of your centrifuge. Please read this manual thoroughly before operating the device.
2. Informació de seguretat
Observeu sempre les següents precaucions de seguretat per evitar lesions i danys a l'instrument:
- Assegureu-vos que la centrífuga estigui col·locada sobre una superfície estable i anivellada.
- Do not operate the centrifuge with an unbalanced rotor.
- Always close the lid securely before starting a run.
- No obriu la tapa fins que el rotor s'hagi aturat completament.
- Use only rotors and accessories approved by Ohaus for this model.
- Desconnecteu l'alimentació abans de netejar o realitzar tasques de manteniment.
- Avoid spilling liquids inside the centrifuge. In case of spillage, clean immediately.
- Wear appropriate personal protective equipment (PPE) when handling samples.
3. Configuració
3.1 Desembalatge
Carefully remove the centrifuge from its packaging. Inspect the unit for any signs of damage during transit. Retain the original packaging for future transport or storage.
3.2 Col·locació
Place the centrifuge on a sturdy, level, and vibration-free workbench. Ensure there is adequate clearance (at least 10 cm) around the unit for proper ventilation. Avoid direct sunlight and areas with extreme temperature fluctuations.
3.3 Connexió d'alimentació
Connect the provided power cord to the centrifuge's power inlet and then to a grounded 120V AC power outlet. Ensure the power switch is in the OFF position before connecting.
3.4 Rotor Installation
Open the centrifuge lid. Carefully place the desired rotor onto the motor shaft, ensuring it seats properly. Secure the rotor using the provided rotor nut or tool, tightening it firmly but not excessively. Refer to your specific rotor manual for detailed installation instructions.
Figure 1: Ohaus FC5706 Frontier 5000 Series Multi-Function Centrifuge. The image displays the centrifuge unit with its grey and white casing, a clear lid, and a control panel featuring an LCD display for RPM/RCF and Time settings, along with control buttons for Start, Stop, Door Open, and adjustment knob.
4. Instruccions de funcionament
4.1 Tauler de control acabatview
The control panel features an intuitive interface for setting and monitoring centrifugation parameters:
- RPM/RCF Display: Shows the current rotational speed in Revolutions Per Minute (RPM) or Relative Centrifugal Force (RCF). The "no" and "6000" on the display indicate the current setting.
- Accel/Decel Display: Indicates the acceleration and deceleration rates (e.g., "77" and "9" as seen on the display).
- Visualització de l'hora: Shows the set run time in minutes and seconds (e.g., "99:99").
- Botó d'inici: Initiates the centrifugation run.
- Botó d'aturada: Halts the current run.
- Botó d'obertura de la porta: Unlocks and opens the centrifuge lid when the rotor is stationary.
- Botó d'ajust: Used to navigate menus and adjust parameter values.
- RPM/RCF Button: Toggles between RPM and RCF display and setting modes.
- Accel/Decel Button: Allows adjustment of acceleration and deceleration profiles.
- Botó d'hora: Allows adjustment of the run time.
4.2 Funcionament bàsic
- Ensure the centrifuge is powered on and the lid is open.
- Càrreguesamples into the rotor buckets, ensuring they are balanced. Use counterweights or balance tubes if necessary.
- Close the centrifuge lid firmly until it latches.
- Set the desired parameters (RPM/RCF, Time, Accel/Decel) using the adjustment knob and corresponding buttons.
- Premeu el botó Comença botó per començar la carrera.
- Monitor the display for current status.
- Once the run is complete and the rotor has stopped, press the Porta Oberta button to unlock the lid.
- Carefully remove your samples.
4.3 Configuració de paràmetres
Per definir paràmetres:
- Premeu el botó RPM/RCF button to toggle between RPM and RCF mode. Use the adjustment knob to set the desired value.
- Premeu el botó Temps button. Use the adjustment knob to set the desired run time in minutes and seconds.
- Premeu el botó Accel/Decel button. Use the adjustment knob to select the desired acceleration and deceleration profiles. Higher numbers typically mean faster rates.
5. Manteniment
5.1 Neteja
Una neteja regular garanteix un rendiment i una longevitat òptims:
- Desconnecteu sempre el cable d'alimentació abans de netejar.
- Netegeu les superfícies exteriors amb un drap suau dampened with mild detergent or a laboratory-grade disinfectant. Avoid abrasive cleaners.
- Clean the rotor chamber and rotor regularly to remove any spills or debris. Use a non-corrosive cleaning solution.
- Ensure all parts are completely dry before reassembling or operating the centrifuge.
5.2 Rotor Care
Inspect rotors for corrosion, cracks, or damage before each use. Clean rotors according to the manufacturer's instructions. Do not use damaged rotors.
5.3 Emmagatzematge
If storing the centrifuge for an extended period, ensure it is clean and dry. Store in a cool, dry place away from direct sunlight and extreme temperatures. Keep the lid slightly ajar to allow air circulation and prevent moisture buildup.
6. Solució De Problemes
Consulteu la taula següent per veure els problemes habituals i les seves solucions:
| Problema | Causa possible | Solució |
|---|---|---|
| Centrifuge does not power on. | No hi ha alimentació; cable d'alimentació fluix; interruptor apagat. | Check power connection; ensure switch is ON; check outlet. |
| Lid does not open. | Rotor still spinning; power failure; lid lock malfunction. | Wait for rotor to stop; check power; contact service if persistent. |
| Vibració excessiva durant el funcionament. | Unbalanced rotor/samples; centrifuge not on level surface; damaged rotor. | Balance samples; ensure level placement; inspect rotor for damage. |
| Missatge d'error a la pantalla. | Specific error condition (e.g., over-speed, over-temperature). | Refer to the specific error code in the full service manual or contact support. |
7. Especificacions
Key technical specifications for the Ohaus FC5706 Frontier 5000 Series Multi-Function Centrifuge:
| Característica | Detall |
|---|---|
| Número de model | 30130876 (FC5706) |
| Font d'alimentació | 120 V AC |
| Mostra | LCD, backlight, 2 lines |
| Tipus de motor | Brushless, quiet motor |
| Petjada | Disseny d'empremta petita |
| Instal·lació | Easy installation design |
| Dimensions del paquet | 21.25 x 16 x 15.25 polzades |
| Pes | 1 Pound (shipping weight, actual unit weight may vary) |
| Primera data disponible | 29 de juny de 2018 |
8. Garantia i Suport
8.1 Informació de la garantia
Ohaus products are warranted against defects in materials and workmanship for a specified period from the date of purchase. Please refer to the warranty card included with your product or visit the official Ohaus weblloc web per obtenir informació detallada sobre els termes i condicions de la garantia.
8.2 Suport tècnic
For technical assistance, service, or spare parts, please contact your local Ohaus distributor or visit the Ohaus official website for support resources and contact information. When contacting support, please have your model number (FC5706) and serial number ready.
Ohaus Official Weblloc: www.ohaus.com
