Introducció
Thank you for choosing the Sunco LED Wraparound Shop Light. This manual provides essential information for the safe installation, operation, and maintenance of your new lighting fixture. Please read these instructions thoroughly before installation and retain them for future reference.
Informació de seguretat
- ADVERTIMENT: Risc de descàrrega elèctrica. Desconnecteu l'alimentació al fusible o al disjuntor abans de la instal·lació o el manteniment.
- Aquest producte s'ha d'instal·lar d'acord amb el codi d'instal·lació aplicable per una persona familiaritzada amb la construcció i el funcionament del producte i els perills que comporta.
- Assegureu-vos el subministrament voltage is compatible with the fixture (120-277V).
- Do not handle live wires.
- No modifiqueu l'aparell. Qualsevol modificació pot anul·lar la garantia i crear riscos per a la seguretat.
- Apte per a damp ubicacions.
Contingut del paquet
Verifiqueu que tots els components siguin presents abans de començar la instal·lació:
- LED Wraparound Shop Light Fixture (2 units for 2-pack)
- Maquinari de muntatge
- Linking Cables (for connecting multiple fixtures)
- Manual d'instruccions
Especificacions
| Número de model | SHW-40W-5K-2PK |
| Consum d'energia | 40 watts |
| Sortida de llum | 3500 lúmens |
| Temperatura de color | 5000K de llum del dia |
| Voltage | 120-277V |
| Dimensions | 48 cm de llargada x 5.35 cm d'amplada x 2.36 cm d'alçada |
| Angle del feix | 110 graus |
| CRI | 80+ |
| Tipus d'instal·lació | Flush Mount / Hardwired |
| Característiques especials | Prismatic Lens, Linkable (up to 8 units), Non-Dimmable |
| Certificacions | ETL |
Instruccions d'instal·lació
This fixture is designed for direct surface mounting to the ceiling. Always ensure power is disconnected before starting installation.
- Prepareu el dispositiu: Carefully remove the diffuser (Part B) from the lamp base (Part A) to access the wiring and mounting points.
- Muntar l'aparell: Col·loca la lamp base against the ceiling where you intend to install it. Mark the mounting holes. Use appropriate mounting hardware (screws, anchors) to securely attach the lamp base to the ceiling.
- Cablejat: Bring the electrical supply wires from the junction box to the fixture. Connect the wires according to local electrical codes: Black to Black (Live), White to White (Neutral), Green/Bare Copper to Green (Ground). Ensure all connections are secure with wire nuts.
- Replace Diffuser: Once wiring is complete and secure, carefully reattach the diffuser to the lamp base. Ensure it snaps firmly into place along both sides.
Enllaçar diversos accessoris
These fixtures are linkable, allowing you to connect up to 8 units from a single power source. Use the provided linking cables or flush linking connectors to connect fixtures end-to-end. Ensure the total wattage of linked fixtures does not exceed the circuit's capacity.
Funcionament
Once properly installed and powered, the Sunco LED Wraparound Shop Light will provide instant-on, flicker-free illumination. This fixture is non-dimmable and operates at a 5000K Daylight color temperature, designed to mimic natural daylight for enhanced visibility and alertness.
Manteniment
The Sunco LED Wraparound Shop Light is designed for long-lasting performance with minimal maintenance. The integrated LED design means there are no bulbs to replace.
- Neteja: Ensure power is off before cleaning. Wipe the fixture and diffuser with a soft, damp cloth. Do not use abrasive cleaners or solvents, as these may damage the finish or optical components.
- Inspecció: Periodically inspect the fixture for any signs of damage or loose connections. If any issues are found, disconnect power and contact a qualified electrician or Sunco Lighting support.
Resolució de problemes
If you experience issues with your Sunco LED Wraparound Shop Light, refer to the following common problems and solutions:
| Problema | Causa possible | Solució |
|---|---|---|
| La llum no s'encén | Sense subministrament elèctric; Cablejat solt; Accessori defectuós. | Check circuit breaker/fuse. Ensure all wire connections are secure. If problem persists, contact Sunco support. |
| La llum és tènue o parpelleja | Incompatible dimmer switch (fixture is non-dimmable); Loose wiring; Power fluctuation; Fixture nearing end of life. | Ensure no dimmer switch is used. Check wiring connections. If dimming occurs after extended use (e.g., 1.5-2 years), it may indicate a component issue. Contact Sunco support for warranty assistance. |
| Only some linked lights are working | Loose linking cable connection; Faulty individual fixture in the chain. | Check all linking cable connections. Isolate the non-working fixture to determine if it's an individual unit issue. |
If troubleshooting steps do not resolve the issue, please contact Sunco Lighting customer support.
Garantia i Suport
Sunco Lighting stands behind the quality of its products. This LED Wraparound Shop Light comes with a Protecció d'7 any warranty. For warranty claims, technical assistance, or any questions regarding your product, please contact our knowledgeable support specialists.
Informació de contacte: Please refer to the Sunco Lighting weblloc web o la documentació de compra per obtenir les dades de contacte més actualitzades.
