Manual d'usuari del provador de baixa resistència de CC Jinko JK2511

1. Introducció

The Jinko JK2511 DC Low Resistance Tester is an intelligent instrument designed for precise measurement of low DC resistance. It offers a wide measurement range and high precision, making it suitable for various industrial applications. This tester is ideal for measuring the copper resistance of transformer and inductor windings, contact resistance of relays and switches, resistance of wire connectors, solder contact resistance of components, and resistance of PCB lines and vias. Its capabilities extend to metal detection and integration into production lines, where it can output good/bad product signals via HANDLER or optional GPIB interfaces to enhance automated testing.

2. Informació de seguretat

Please read and understand all safety instructions before operating the JK2511 DC Low Resistance Tester. Failure to follow these instructions may result in injury or damage to the instrument.

• Always connect the instrument to a properly grounded power outlet.
• Do not operate the instrument in wet or damp condicions.
• Assegureu-vos que totes les connexions estiguin segures abans d'aplicar energia.
• Avoid touching live circuits.
• Refer to qualified service personnel for any repairs or maintenance not covered in this manual.
• Disconnect power before cleaning or servicing the instrument.

3. Producte acabatview

3.1 Tauler frontal

Figura 1: Davant view of the Jinko JK2511 DC Low Resistance Tester, showing the digital display, control buttons, and input terminals. The display shows "8.8.8.8.8" with units for mΩ, Ω, and kΩ. The left side has a red POWER button. The right side features navigation and function buttons labeled HIGH, PASS, LOW, HOLD, and SETUP.

3.2 lateral View

Figura 2: lateral view of the Jinko JK2511 DC Low Resistance Tester, illustrating the depth and general form factor of the device. This angle highlights the robust casing and ventilation slots on the side.

3.3 Darrera View

Figura 3: posterior view of the Jinko JK2511 DC Low Resistance Tester, showing the ventilation grille and the overall construction from the back. This view typically includes power input and communication ports, though they are not clearly visible in this specific image.

4. Configuració

1. Desembalatge: Carefully remove the JK2511 tester from its packaging. Inspect for any signs of damage during transit. Retain the packaging for future storage or shipping.
2. Connexió d'alimentació: Connect the provided power cord to the instrument's power input and then to a grounded AC power outlet. Ensure the voltage matches the instrument's requirements.
3. Connexió de la sonda: Connect the test probes to the appropriate input terminals on the front panel. Typically, these are labeled SENSE+, SENSE-, DRIVE+, and DRIVE-. Ensure a secure connection for accurate measurements.
4. Encesa inicial: Press the red POWER button on the front panel to turn on the instrument. The display should illuminate, indicating the device is operational.
5. Autocomprovació: The instrument may perform a brief self-test upon startup. Wait for this process to complete before proceeding with measurements.

5. Instruccions de funcionament

5.1 Mesura bàsica

1. Connecteu el DUT: Connect the Device Under Test (DUT) to the test probes. Ensure good contact between the probes and the measurement points on the DUT.
2. Select Measurement Range: The JK2511 typically auto-ranges. If manual range selection is available, use the appropriate buttons (e.g., SETUP or navigation keys) to select a range suitable for the expected resistance value.
3. Iniciar la mesura: The instrument usually displays the resistance value continuously. For a stable reading, press the MANTENIM button to freeze the display.
4. Llegeix la pantalla: Observe the resistance value shown on the digital display, along with the corresponding unit (mΩ, Ω, or kΩ).

5.2 Advanced Features (If Applicable)

• Limit Testing (HIGH/PASS/LOW): The instrument supports setting upper and lower resistance limits. Use the CONFIGURACIÓ menu to configure these limits. The ALTA, PASSA, i BAIXA indicators will illuminate to show if the measured resistance falls above, within, or below the set limits.
• Conservació de dades: Premeu el botó MANTENIM button to freeze the current measurement on the display. Press it again to release and resume continuous measurement.
• Funció de posada a zero: For highly accurate low resistance measurements, a zeroing function may be available to compensate for test lead resistance. Consult the full manual for specific instructions on performing a zero adjustment.
• Interface Communication: For automated testing, connect the instrument to a PC or PLC via the HANDLER interface or optional GPIB interface. Refer to the communication protocol documentation for programming details.

6. Manteniment

• Neteja: Disconnect power before cleaning. Use a soft, dry cloth to wipe the exterior of the instrument. Do not use abrasive cleaners or solvents.
• Cura de la sonda: Keep test probes clean and free from corrosion. Replace damaged probes immediately to ensure accurate measurements and safety.
• Emmagatzematge: When not in use, store the instrument in a clean, dry environment, away from direct sunlight and extreme temperatures.
• Calibració: Regular calibration by qualified personnel is recommended to maintain measurement accuracy, especially for critical applications.

7. Solució De Problemes

This section provides solutions to common issues. For problems not listed here, contact Jinko customer support.

• Instrument does not power on:
  • Check if the power cord is securely connected to both the instrument and the power outlet.
  • Comproveu que la presa de corrent funcioni.
  • Check the instrument's fuse, if accessible and user-replaceable (refer to the full manual).
• Lectures inexactes o inestables:
  • Ensure test probes are making good, clean contact with the DUT.
  • Check for damaged or worn test leads.
  • Verify that the DUT is properly isolated and not influenced by external electrical noise.
  • Perform a zero adjustment if available.
  • Consider if the instrument requires calibration.
• Display shows "OVERLOAD" or "OL":
  • The measured resistance may be higher than the selected range. If auto-ranging, this indicates the resistance is beyond the instrument's maximum capability.
  • Check for open circuits in the DUT or test leads.

8. Especificacions

Note: Full technical specifications, including measurement ranges, accuracy, and environmental conditions, are available in the complete product datasheet.

9. Garantia i Suport

Jinko provides a standard warranty for the JK2511 DC Low Resistance Tester against defects in materials and workmanship. The specific terms and duration of the warranty may vary by region. Please retain your proof of purchase for warranty claims.

For technical support, service, or warranty inquiries, please contact Jinko customer service through their official weblloc web o la informació de contacte proporcionada amb la compra.

• Assistència en línia: Visit the official Jinko weblloc web per a preguntes freqüents, actualitzacions de programari i recursos addicionals.
• Informació de contacte: Refer to the product packaging or Jinko's official weblloc web per obtenir les dades de contacte més actualitzades.