1. Introducció
This manual provides essential instructions for the installation, maintenance, and general information regarding the Franke Oven Door Seal, part numbers 1999170 and 1330169205. This seal is designed to ensure proper heat retention and energy efficiency in compatible Franke ovens. Please read these instructions carefully before proceeding with installation or maintenance.
2. Descripció i compatibilitat del producte
The Franke Oven Door Seal (part numbers 1999170, 1330169205) is a four-sided gasket equipped with hooks for secure attachment. It measures approximately 1450 mm in length and is designed as a direct replacement for specific Franke oven models.
Image 1: The Franke Oven Door Seal 1999170 / 1330169205. This image shows the black, rectangular oven door seal with rounded corners, designed to fit around the oven door opening.
Compatible Franke Oven Models:
This seal is adaptable to various Franke oven models. Please verify your oven's model number against the list below to ensure compatibility. If your model is not listed, please contact Franke customer support or your supplier for assistance.
- Franke Oven CR 66 M BM VC PRG (5600307)
- Franke Oven D. G 52 M XS 2L INOX SAT. PRG (5600260)
- Franke Oven TECH 603 IND NEGRO PRG (5600221)
- Franke Oven TECH 603 IND BLANCO PRG (5600222)
- Franke Oven DC 97 XM (5600118)
- Franke Oven TECH 603 COMBI 5 INOX PRG (5701010101010101010101010101010101) - Note: This model number appears truncated in the source data.
- Franke Oven TECH 603 COMBI NEGRO PRG (5700102)
- Franke Oven TECH 603 COMBI 5 NEGRO PRG (5700103)
- Franke Oven TECH 603 COMBI BLANCO PRG (5700104)
- Franke Oven TECH 603 COMBI 5 BLANCO PRG (5700105)
- Franke Oven TECH 604 COMBI INOX PRG (5700106)
- Franke Oven GA 74 M OA Avena FRAG (5600121)
- Franke Oven GA 74 M OW (5600159)
- Franke Oven GA 74 M GF Graphite FRAG (5600122)
- Franke Oven GA 74 M SH SAHARA FRAG (5600123)
- Franke Oven El. GA 74 M CO (5600160)
- Franke Oven El. GA 74 M SG (5600196)
- Franke Oven TECH 603 COMBI INOX PRG (5700100)
- Franke Oven SM 66 M XS *S PRG (5600338)
- Franke Oven CM 74 M GF Graphite FRAG (5600126)
- Franke Oven CM 74 M SH SAHARA FRAG (5600127)
- Franke Oven KU 52 M XS (5600147)
- Franke Oven DMX 74 XM XXS INOX SAT. (5600114)
- Franke Oven DM 97 M XAXX ANTITOUCH (5600116)
- Franke Oven DC 72 XM XXS SAT. (5600117)
- Franke Oven EM 74 M OA FRAG (5600128)
- Franke Oven EM 74 M GF Graphite FRAG (5600129)
- Franke Oven EM 74 M SH SAHARA FRAG (5600130)
- Franke Oven EM 74 M CO RAMÉ (5600131)
- Franke Oven SM 62 M XS *S PRG (5600337)
- Franke Oven SM 62 M XS (5600328)
- Franke Oven SM 66 M XS (5600329)
- Franke Oven SM 86 M XS (5600331)
- Franke Oven SM 981 M XS (5600332)
- Franke Oven SG 62 M SH 5SH (5600327)
- Franke Oven SG 62 M GF (5600326)
- Franke Oven SG 62 M SL (5600325)
- Franke Oven SG 62 M MI (5600323)
- Franke Oven SG 62 M OA (5600324)
- Franke Oven El. AD 72 M SG (5600212)
- Franke Oven NE 98 M BK (5600219)
- Franke Oven DG 52 M XXL INOX SAT. PRG (5600261)
- Franke Oven DG 56 M XS 2L INOX (5600262)
3. Configuració i instal·lació
Replacing an oven door seal is a straightforward process, but requires careful attention to safety and detail.
Precaucions de seguretat:
- Desconnecteu l'alimentació: Always ensure the oven is completely disconnected from the main power supply before beginning any installation or maintenance.
- Permetre la refrigeració: If the oven has been recently used, allow it to cool down completely to prevent burns.
- Porteu guants: Protective gloves are recommended to prevent cuts or scrapes from sharp edges.
Passos d'instal·lació:
- Open Oven Door: Fully open the oven door to access the existing seal.
- Treure el segell antic: Carefully pull the old seal away from the oven frame. Most oven seals are held in place by hooks that fit into small holes around the oven opening. Gently unhook each attachment point.
- Clean Seal Groove: Once the old seal is removed, thoroughly clean the groove or channel where the seal sits. Remove any food debris, grease, or residue that could prevent the new seal from seating properly. A mild degreaser and a soft cloth are recommended.
- Instal·leu un segell nou: Starting from one corner, carefully push the hooks of the new Franke oven door seal into the corresponding holes around the oven frame. Work your way around the entire perimeter, ensuring each hook is securely seated. The seal should fit snugly without any gaps or twists.
- Close and Test Door: Gently close the oven door to ensure the new seal compresses evenly. Open and close the door a few times to confirm proper seating.
- Torneu a connectar l'alimentació: Once you are certain the seal is correctly installed, reconnect the oven to the main power supply.
- Perform Heat Test (Optional): Turn on the oven to a low temperature for a short period and carefully check for any heat leakage around the door edges. If heat is escaping, the seal may not be installed correctly, or there might be an issue with the door hinges.
4. Manteniment
Regular maintenance of your oven door seal can extend its lifespan and ensure optimal oven performance.
- Neteja regular: Periodically wipe down the oven door seal with a damp cloth and mild detergent to remove food splatters and grease. Avoid abrasive cleaners or harsh chemicals, as these can damage the seal material.
- Inspeccionar per danys: Routinely check the seal for any signs of wear, tears, cracks, or hardening. A damaged seal will not effectively retain heat.
- Eviteu pessigar: Be careful not to pinch the seal with oven racks or baking trays when loading or unloading the oven.
- Substituïu quan sigui necessari: If the seal shows significant signs of wear or if you notice heat escaping from the oven door, it is time to replace it to maintain energy efficiency and cooking performance.
5. Solució De Problemes
If you encounter issues after installing the new oven door seal, consider the following:
- Heat Leaking from Oven Door:
- Ensure the seal is correctly seated in its groove and all hooks are securely attached.
- Check for any twists or kinks in the seal that might prevent a tight closure.
- Inspect the oven door hinges; worn hinges can prevent the door from closing properly, regardless of the seal's condition.
- Seal Does Not Fit:
- Double-check the part numbers (1999170 or 1330169205) against your oven's required seal.
- Verify your oven model is listed in the compatibility section.
- Ensure you have the correct type of seal (e.g., 4-sided with hooks).
6. Especificacions
| Brand (Part) | Franke |
| Números de part | 1999170, 1330169205 |
| Tipus | Oven Door Seal, 4-sided with hooks |
| Longitud | Aproximadament 1450 mm |
| Pes de l'article | 110 grams |
| Dimensions del paquet | 29.6 x 24.1 x 2.5 cm |
7. Garantia i Suport
Information regarding specific warranty terms for this replacement part is not provided in the product details. For warranty inquiries, technical support, or further assistance with compatibility, please contact the original manufacturer, Franke, or the retailer from whom you purchased the seal. Please have your oven model number and the seal's part numbers (1999170 or 1330169205) ready when contacting support.
Note: Spare parts availability information is currently unavailable according to product specifications.
