Introducció
The JBL GO2 is a full-featured waterproof portable Bluetooth speaker designed for on-the-go audio. This manual provides essential information for setting up, operating, maintaining, and troubleshooting your device to ensure optimal performance.
Imatge: Frontal view of the JBL GO2 speaker in blue, showcasing its compact design and JBL logo.
Què hi ha a la caixa
Verifiqueu que hi hagi tots els elements en desembalar-los:
- JBL GO2 Speaker
- Cable micro USB (per carregar)
- Guia d'inici ràpid (aquest document)
Configuració
1. Carregant l’altaveu
Before first use, fully charge the JBL GO2 speaker. Connect the supplied Micro USB cable to the charging port on the speaker and the other end to a USB power adapter (not included). The charging indicator light will illuminate during charging and turn off when fully charged. A full charge takes approximately 2.5 hours.
Imatge: Lateral view of the JBL GO2 speaker, highlighting the Micro USB charging port and 3.5mm auxiliary input, both protected by a waterproof flap.
2. Encès / apagat
Press and hold the power button located on the top of the speaker for approximately 2 seconds to power on or off. A distinct audio cue will indicate the power status.
3. Emparellament Bluetooth
- Power on the JBL GO2 speaker. The Bluetooth indicator light will flash blue, indicating it is in pairing mode.
- Al dispositiu mòbil, navega fins a la configuració de Bluetooth.
- Select "JBL GO2" from the list of available devices.
- Once connected, the Bluetooth indicator light will turn solid blue, and an audio cue will confirm the connection.
4. Connexió auxiliar
For devices without Bluetooth, connect an audio cable (not included) from your device's headphone jack to the 3.5mm auxiliary input port on the JBL GO2 speaker. The speaker will automatically switch to auxiliary mode.
En funcionament
1. Reproducció de música
After connecting via Bluetooth or auxiliary cable, begin playing audio from your source device. Use the controls on your device or the speaker to manage playback.
2. Control de volum
Adjust the volume using the '+' and '-' buttons located on the top of the speaker. You can also control the volume from your connected device.
Imatge: Superior view of the JBL GO2 speaker, showing the power, Bluetooth pairing, volume up, volume down, and play/pause/speakerphone buttons.
3. Funció d'altaveu
The JBL GO2 features a built-in noise-cancelling speakerphone. When a call is received while connected via Bluetooth:
- Press the play/pause button once to answer an incoming call.
- Press the play/pause button once again to end the call.
- Press and hold the play/pause button to reject an incoming call.
4. Waterproof Usage (IPX7)
The JBL GO2 is IPX7 waterproof, meaning it can be submerged in water up to 1 meter (3 feet) for up to 30 minutes. Ensure the charging port and auxiliary input port covers are securely closed before exposing the speaker to water.
Important:
- Do not expose the speaker to salt water or other liquids.
- Always ensure the port covers are sealed to maintain waterproofing.
Manteniment
1. Neteja
Netegeu l'altaveu amb un suau, damp cloth. Do not use abrasive cleaners or solvents. For stubborn dirt, a mild soap solution can be used, followed by rinsing with fresh water if the port covers are sealed.
2. Emmagatzematge
Guardeu l'altaveu en un lloc fresc i sec, allunyat de la llum solar directa i de temperatures extremes. Si l'emmagatzemeu durant un període prolongat, carregueu la bateria periòdicament per mantenir-ne la vida útil.
3. Post-Water Exposure Care
After exposure to water, gently shake the speaker to remove excess water from the grille and ports. Allow it to air dry completely before charging or connecting any cables.
Resolució de problemes
| Problema | Causa possible | Solució |
|---|---|---|
| L'altaveu no s'encén | La bateria s’ha esgotat | Charge the speaker using the Micro USB cable. |
| Sense so | Volume is too low or muted; Device not connected | Increase volume on speaker and source device; Ensure proper Bluetooth or auxiliary connection. |
| L'aparellament de Bluetooth falla | L'altaveu no està en mode d'emparellament; el dispositiu és massa lluny; l'interferència | Ensure speaker is in pairing mode (flashing blue light); Move device closer; Turn off other Bluetooth devices. |
| Poor audio quality via Bluetooth | Device too far; Obstructions; Low battery | Move device closer to speaker; Remove obstructions; Charge the speaker. |
Especificacions
| Característica | Detall |
|---|---|
| Nom del model | Aneu 2 |
| Tecnologia de comunicació sense fils | Bluetooth |
| Tecnologia de connectivitat | Auxiliar, Bluetooth |
| Nivell de resistència a l'aigua | IPX7 impermeable |
| Hora de joc | Fins a 5 hores (varia segons el nivell de volum i el contingut d'àudio) |
| Temps de càrrega | Aproximadament 2.5 hores |
| Potència de sortida màxima dels altaveus | 5 watts |
| Resposta de freqüència | 20 kHz |
| Dimensions del producte (P x A x A) | 7.9 cm x 21.8 cm x 18 cm (aprox. 3.1 cm x 8.6 cm x 7.1 cm) |
| Pes de l'article | 6.5 unces (aprox. 184 grams) |
| Entrada Voltage | 5 Volts |
| Interval Bluetooth | 10 metres (33 peus) |
| Característiques especials | Built-in Microphone, Waterproof |
Garantia i Suport
Informació de la garantia
The JBL GO2 speaker comes with a limited warranty. Please refer to the warranty card included with your product or visit the official JBL weblloc web per obtenir informació detallada sobre els termes i condicions de la cobertura i la durada de la garantia.
Atenció al client
Per a més ajuda, assistència tècnica o consultes de servei, visiteu el lloc web oficial de suport de JBL. weblloc web o poseu-vos en contacte amb el seu departament d'atenció al client. Normalment, podeu trobar la informació de contacte al lloc web de JBL weblloc o a l'embalatge del producte.
