Antari Z-390 High-Capacity 1500-Watt DMX Fazer

Introducció

The Antari Z-390 is a high-capacity 1500-watt DMX Fazer designed for professional stage and event applications. This unit offers significant improvements over its predecessor, the Z-380, including a larger 4-liter fluid tank for extended operation and approximately 30% higher haze output. This manual provides essential information for the safe and efficient operation, setup, maintenance, and troubleshooting of your Z-390 Fazer.

Característiques clau

• Entrada Voltage: US model : AC 100-120V, 50/60Hz 8.5A
• Rated Power: 1000W (120V)
• Warm Up Time: 1.5 minutes (approx.)
• Fluid Consumption: 8mL/min

Configuració

Before operating the Antari Z-390, ensure it is placed on a stable, level surface in a well-ventilated area. Keep a safe distance from flammable materials and ensure proper clearance around the unit for air circulation.

1. Desembalatge i inspecció

Carefully remove the Z-390 from its packaging. Inspect the unit for any signs of damage that may have occurred during shipping. If any damage is found, contact your dealer immediately.

2. Fluid Tank Installation

Locate the 4-liter fluid tank. Fill the tank only with Antari-approved haze fluid. Insert the fluid tube into the tank and securely place the tank into its designated compartment on the unit.

Image: The Antari Z-390 Fazer with its 4-liter fluid tank properly installed on top of the unit, ready for operation.

3. Connexió d'alimentació

Connect the power cord to the power inlet on the rear of the unit, then plug it into a grounded electrical outlet. Ensure the power switch is in the OFF position before connecting to power.

Imatge: Part posterior view of the Antari Z-390 Fazer, highlighting the power inlet, DMX input/output ports, and control panel.

4. Connexió DMX (opcional)

For DMX control, connect a DMX cable from your DMX controller to the DMX IN port on the Z-390. If daisy-chaining multiple units, connect from the DMX OUT of the Z-390 to the DMX IN of the next unit.

Instruccions de funcionament

1. Power On and Warm-up

Flip the power switch to the ON position. The unit will begin its warm-up cycle, which takes approximately 1.5 minutes. The display will indicate when the unit is ready to faze.

2. Funcionament manual

Once warmed up, you can manually trigger haze output using the control panel on the unit or an optional wired remote control. Refer to the display for current status and settings.

3. Funcionament DMX

Set the DMX address on the Z-390 according to your DMX controller's configuration. The Z-390 typically uses a specific number of DMX channels for haze output, fan speed, and special functions. Consult your DMX controller's manual for programming instructions.

Image: The Antari Z-390 Fazer actively producing a steady stream of haze, demonstrating its output capability in a dark setting.

Image: A wider shot of the Antari Z-390 Fazer emitting haze, illustrating the broad dispersion and atmospheric effect it creates.

4. Fluid Consumption

The Z-390 consumes fluid at a rate of approximately 8mL/min. Monitor the fluid level in the tank and refill as needed to ensure continuous operation and prevent damage to the pump.

Manteniment

Regular maintenance is crucial for the longevity and optimal performance of your Antari Z-390 Fazer.

1. Fluid Type

Always use Antari-approved haze fluid. Using other types of fluid can cause clogs, damage the pump, and void your warranty.

2. Neteja

Periodically clean the exterior of the unit with a soft, dry cloth. Ensure the air vents are free from dust and debris to prevent overheating. Do not use solvents or abrasive cleaners.

3. Emmagatzematge

When not in use for extended periods, drain any remaining fluid from the tank. Store the unit in a cool, dry place, away from direct sunlight and extreme temperatures.

Resolució de problemes

This section addresses common issues you might encounter with your Antari Z-390 Fazer.

Especificacions tècniques