NIBCO Fig No 5811-C 4-inch ABS DWV Cleanout Tee Instruction Manual

1. Introducció

This manual provides essential information for the proper installation, use, and maintenance of the NIBCO Fig No 5811-C 4-inch ABS DWV Cleanout Tee. This product is designed for use in non-pressure drain, waste, and vent (DWV) systems. Adherence to these instructions is crucial for safe and effective operation.

2. Informació de seguretat

ADVERTIMENT: Do not test or use this product with compressed air or other gases. Doing so can result in product failure and severe injury or death. This fitting is intended for non-pressure liquid and waste drainage applications only.

Advertència de la proposta 65: Aquest producte pot contenir productes químics coneguts per l'estat de Califòrnia per causar càncer i defectes de naixement o altres danys reproductius. Rentar-se les mans després de la manipulació.

Always wear appropriate personal protective equipment (PPE), including safety glasses and gloves, when handling ABS pipe and fittings and when working with solvent cement.

3. Producte acabatview

The NIBCO Fig No 5811-C is a 4-inch ABS DWV Cleanout Tee. It features a hub x hub connection type, designed for solvent welding into a drainage system. The cleanout tee allows for access to the drainage system for inspection and clearing blockages.

Figure 1: NIBCO Fig No 5811-C 4-inch ABS DWV Cleanout Tee. This image shows the black ABS fitting with three hub connections, designed for solvent welding into a drainage system.

Figura 2: Alternativa view of the NIBCO 4-inch ABS DWV Cleanout Tee. This perspective highlights the internal structure and the smooth finish of the ABS material.

Característiques principals:

• Material: Acrilonitril butadiè estirè (ABS)
• Mida: 4 polzades
• Connection Type: Hub x Hub (Solvent Weld)
• Application: Non-pressure Drain, Waste, and Vent (DWV) systems
• Function: Provides access for cleaning and inspection

4. Configuració i instal·lació

Proper installation of ABS DWV fittings requires careful attention to detail and the use of appropriate solvent cement. Follow local plumbing codes and manufacturer guidelines.

Eines i materials necessaris:

• ABS Pipe Cutter or Saw
• Deburring Tool or File
• Cinta mètrica
• Marcador
• ABS Solvent Cement (specifically formulated for ABS)
• Applicator (often included with solvent cement)
• Draps nets
• Personal Protective Equipment (PPE): Safety glasses, gloves

Passos d'instal·lació:

1. Preparació: Ensure all pipe ends and fitting hubs are clean, dry, and free from grease or debris. Cut pipe ends squarely and deburr both inside and outside edges to prevent flow restriction and ensure proper fit.
2. Ajust en sec: Test fit the pipe into the fitting hub. The pipe should enter the hub easily for about 1/3 to 2/3 of the hub depth. A snug fit is essential for a strong solvent weld.
3. Marcatge: Mark the pipe and fitting to ensure proper alignment during the solvent welding process, especially for complex assemblies.
4. Aplicar ciment solvent: Apply a liberal, even coat of ABS solvent cement to the outside of the pipe end and a thinner, even coat to the inside of the fitting hub. Work quickly, as ABS cement dries rapidly.
5. Uneix canonades i accessoris: Immediately insert the pipe into the fitting hub with a 1/4 turn twist until the pipe bottoms out against the stop. Hold the joint firmly for at least 30 seconds to allow the cement to set and prevent the pipe from backing out.
6. Curat: Wipe off any excess cement from the joint. Allow the joint to cure for the recommended time specified by the solvent cement manufacturer before testing the system. This typically ranges from 30 minutes to several hours, depending on temperature and humidity.
7. Cleanout Plug: Ensure the cleanout opening is properly sealed with an appropriate cleanout plug (sold separately) after installation.

5. Principis de funcionament

The NIBCO ABS DWV Cleanout Tee functions as a critical component in a non-pressure drainage system. Its primary purpose is to facilitate the removal of wastewater and solids while providing an access point for maintenance. The cleanout port allows for the insertion of drain cleaning tools to clear blockages without disassembling the entire pipe system.

6. Manteniment

Once installed, the NIBCO ABS DWV Cleanout Tee requires minimal maintenance. Regular inspection of the DWV system for leaks or signs of damage is recommended. Ensure the cleanout plug is securely tightened to prevent leaks and odors. If a blockage occurs, access the system through the cleanout port using appropriate drain cleaning equipment.

Avoid pouring harsh chemicals that are not compatible with ABS plastic down the drain, as this can degrade the material over time.

7. Solució De Problemes

Problemes comuns:

• Fuites a les juntes:

  Possible causa: Improper solvent welding, insufficient cement, or inadequate curing time.

  Solució: For minor leaks, re-apply cement if the joint is still pliable and within the working time. For cured leaks, the joint may need to be cut out and replaced. Ensure proper technique and curing time during installation.

• Blockages:

  Possible causa: Accumulation of debris, grease, or foreign objects in the drainage system.

  Solució: Access the system through the cleanout tee. Use a plumbing snake or auger to clear the obstruction. Avoid using excessive force that could damage the pipe.
• Odors from Cleanout:

  Possible causa: Loose or missing cleanout plug.

  Solució: Ensure the cleanout plug is securely tightened. Replace damaged or missing plugs immediately.

8. Especificacions

9. Garantia i Suport

For information regarding product warranty, technical support, or further assistance, please contact NIBCO customer service or visit the official NIBCO weblloc. Conserveu el rebut de compra per a reclamacions de garantia.

Oficial de NIBCO Weblloc: www.nibco.com