1. Introducció
This manual provides essential information for the safe and effective installation, operation, and maintenance of your OSRAM P-VIP TV Lamp Assembly. This high-quality replacement lamp is designed to restore optimal picture brightness and clarity to compatible Mitsubishi rear projection televisions.
Please read this manual thoroughly before attempting any installation or maintenance procedures. Keep this manual for future reference.
Figura 1.1: Davant view of the OSRAM P-VIP TV Lamp Assembly. This image shows the complete lamp module, including the bulb and its housing, ready for installation.
2. Informació important de seguretat
WARNING: Risk of Electric Shock, Burns, and Mercury Exposure.
- Always unplug the television from the power outlet and allow it to cool down completely (at least 30 minutes) before attempting to replace the lamp. Lamps operate at high temperatures and can cause severe burns.
- Do not touch the bare lamp bombeta with your fingers. Oils from your skin can create hot spots on the bulb, leading to premature failure. Handle the lamp assembly by its plastic housing.
- Utilitzeu guants de protecció i protecció ocular during installation to prevent injury from broken glass.
- Aquesta lamp conté mercuri. En el cas de lamp breakage, avoid direct contact with broken glass or mercury. Ventilate the room and follow local regulations for proper disposal of mercury-containing products. Do not dispose of with regular household waste.
- Replace with the same type number. Using an incorrect lamp type can damage your television or pose a safety hazard.
- Do not turn the cartridge over during installation or removal.
Figura 2.1: A dalt view de la lamp assembly housing, showing caution labels for hot surface and mercury content. Always observe these warnings.
3. Compatibilitat
This OSRAM P-VIP TV Lamp Assembly is a direct replacement for the following Mitsubishi TV lamp models:
- Mitsubishi 915B455011
- Mitsubishi 915B455012
- Other Mitsubishi Model Series requiring the 82009 lamp muntatge.
Please verify your TV's required lamp model number before purchase and installation to ensure compatibility.
4. Instruccions d'instal·lació
Follow these steps carefully to replace your TV lamp. Refer to your television's owner's manual for specific instructions regarding lamp access and removal, as procedures may vary by model.
- Prepara la televisió:
- Turn off your Mitsubishi TV.
- Unplug the TV's power cord from the wall outlet.
- Allow the TV and the old lamp to cool down for at least 30 minutes. The lamp operates at very high temperatures.
- Localitza la Lamp Tauler d'accés:
El lamp access panel is typically located on the back or side of the TV. It may be secured with screws. Consult your TV's manual if you cannot locate it.
- Remove the Old Lamp:
- Traieu amb cura els cargols que subjecten la lamp panell d'accés.
- Open or remove the panel.
- Localitza la lamp assembly. It is usually secured by one or more screws or a latch.
- Loosen any retaining screws or release the latch.
- Gently pull the old lamp assembly straight out of its compartment. Do not force it.
- Place the old lamp assembly in a protective bag for proper disposal.
Figura 4.1: lateral view de la lamp assembly, showing the handle for easy removal and insertion.
- Install the New Lamp:
- Unpack the new OSRAM P-VIP TV Lamp Assembly. Handle it by the plastic housing only.
- Align the new lamp assembly with the lamp compartiment.
- Gently slide the new lamp assembly straight into the compartment until it is fully seated. Ensure it clicks into place or aligns with the screw holes.
- Assegureu la lamp assembly with the retaining screws or latch that were removed earlier. Do not overtighten.
Figura 4.2: Primer pla view of the P-VIP bulb within its housing. Ensure the bulb is securely seated before installation.
- Close the Access Panel:
- Substituïu la lamp access panel and secure it with its screws.
- Ensure all panels are properly closed before proceeding.
- Power On and Reset Lamp Temporitzador:
- Plug the TV's power cord back into the wall outlet.
- Enceneu el televisor.
- Consult your TV's owner's manual for instructions on how to reset the lamp timer. Resetting the timer is crucial for accurate lamp life monitoring.
5. Funcionament de la Lamp
Once installed, the OSRAM P-VIP TV Lamp Assembly operates automatically with your television. The lamp will illuminate when the TV is powered on and extinguish when the TV is powered off or enters standby mode.
- Temps d'escalfament: El lamp may require a short warm-up period (a few seconds to a minute) to reach full brightness after being turned on.
- Temps de refredament: After turning off the TV, the internal cooling fan will continue to run for a short period to cool the lamp. Do not unplug the TV during this cool-down cycle, as it can shorten lamp vida.
6. Manteniment i cura
Proper care can help extend the life of your lamp and maintain optimal picture quality.
- Eviteu els cicles freqüents d'encesa/apagada: Repeatedly turning the TV on and off in short intervals can reduce lamp vida.
- Assegureu-vos una ventilació adequada: Do not block the ventilation openings on your TV. Adequate airflow is essential for lamp refredament.
- Clean Air Filters (if applicable): Some TVs have air filters that should be cleaned periodically to ensure proper cooling. Refer to your TV's manual.
- Manejar amb cura: Manegeu sempre la lamp assembly by its plastic housing. Avoid touching the glass bulb.
7. Solució De Problemes
If you experience issues after installing your new lamp, consider the following common solutions:
| Problema | Causa possible | Solució |
|---|---|---|
| TV does not turn on or shows no picture after lamp substitució. | Lamp not fully seated; lamp access panel not closed properly; TV safety switch engaged. | Assegureu-vos que lamp assembly is fully inserted and secured. Close and secure the lamp access panel completely. Unplug the TV, wait 5 minutes, then plug back in. |
| Picture is dim or flickering. | Lamp nearing end of life (unlikely for new lamp); poor ventilation; lamp not fully seated. | Ensure TV ventilation is not blocked. Re-seat the lamp assembly. If the problem persists, contact support. |
| Lamp indicator light on TV remains on or flashes. | Lamp timer not reset; TV detects an issue with the lamp. | Restableix la lamp timer in your TV's menu (refer to TV manual). If the light persists, re-check lamp installation or contact support. |
| Loud fan noise from TV. | Blocked ventilation; TV overheating. | Ensure TV ventilation openings are clear. Clean any air filters if your TV has them. |
If these steps do not resolve the issue, please contact OSRAM customer support or a qualified service technician.
8. Especificacions del producte
| Característica | Detall |
|---|---|
| Marca | OSRAM |
| Tipus de font de llum | P-VIP Projector Lamp |
| Wattage | 100 watts |
| Característica especial | Rendiment de llarga durada |
| Recompte d'unitats | 1.0 recompte |
| Pes de l'article | 1.2 lliures (aprox.) |
| Dimensions del paquet | 9 x 8 x 8 polzades (aprox.) |
| Fabricant | OSRAM |
9. Informació de la garantia
This OSRAM P-VIP TV Lamp Assembly is backed by a Garantia del fabricant de 1 anysAquesta garantia cobreix els defectes de materials i de fabricació en condicions d'ús normal. Si us plau, conserveu el comprovant de compra per a reclamacions de garantia.
For detailed warranty terms and conditions, please refer to the official OSRAM weblloc o contacteu amb el servei d'atenció al client.
10. Customer Support and Authenticity
For technical assistance, troubleshooting, or warranty inquiries, please contact OSRAM customer support through their official channels.
To verify the authenticity of your OSRAM P-VIP lamp, utilize the official "Authenticity Checker" tool available online at OSRAM-ShopYourLight. OSRAM works closely with projector OEMs to ensure bright, crisp, and long-lasting lamp rendiment.
