Manual d'instruccions del pedal de distorsió JHS Pedals Paul Gilbert PG-14 Signature

1. Introducció

The JHS Pedals Paul Gilbert PG-14 is a unique distortion pedal designed to emulate the dynamics and tone of a pushed tube amplifier. It features a FET-based distortion engine and an active mid-frequency preamp for extensive tonal possibilities.

Figura 1: Frontal view of the JHS Pedals Paul Gilbert PG-14 Signature Distortion Pedal.

2. Configuració

Requisits d'energia de 2.1

The PG-14 requires standard 9V DC negative center power. It consumes 67mA of current. Use a regulated power supply for optimal performance and to prevent damage.

2.2 Connexions

Connect your guitar to the input jack (typically on the right side of the pedal). Connect the output jack (typically on the left side) to your amplifier or the next pedal in your signal chain. Ensure all connections are secure.

Figura 2: lateral view showing input and output jacks.

3. Controls i Funcions

The PG-14 features six primary control knobs and a footswitch for engaging the effect.

• VOL (volum): Controls the overall output level of the pedal. Adjust to match or boost your amplifier's clean signal.
• MID (Mid-Frequency Level): Adjusts the level of the selected mid-frequency. This knob works in conjunction with the MID FREQ knob.
• CONDUIR: Controls the amount of distortion or gain. Turning clockwise increases saturation.
• TO: A standard tone control that adjusts the overall brightness or darkness of the distorted signal.
• MID FREQ (Mid-Frequency Selector): Selects the specific frequency range that the MID knob will boost or cut. This active mid-frequency preamp is located at the front of the FET distortion circuitry, offering a vast sweep of tonal possibilities.
• PUSH: This unique control emulates the sag and response of a pushed tube amplifier, allowing for dynamic and touch-sensitive distortion at various volume levels.
• Interruptor de peu: Engages or bypasses the pedal effect.

Figura 3: Angle view highlighting the control knobs.

4. Operating the Pedal

The PG-14 is designed for versatility. Experiment with the controls to find your desired distortion characteristics. The active mid-frequency preamp allows for precise shaping of your tone, making it adaptable to various amplifiers and guitars.

• Start with all knobs at noon (12 o'clock) and adjust gradually.
• Use the DRIVE knob to set your base level of distortion.
• Adjust the TONE knob for overall brightness.
• Utilize the MID FREQ and MID knobs to sculpt your midrange, which is crucial for cutting through a mix or achieving specific vocal-like tones.
• The PUSH knob adds a unique dynamic response, mimicking the feel of a cranked tube amp. Explore its range to find the sweet spot for your playing style.

5. Especificacions

Figure 4: Product dimensions for the PG-14 pedal.

6. Manteniment

To ensure the longevity and optimal performance of your JHS Pedals PG-14, follow these maintenance guidelines:

• Neteja: Feu servir un drap suau i sec per netejar l'exterior del pedal. Eviteu productes de neteja o dissolvents abrasius.
• Emmagatzematge: Guardeu el pedal en un lloc fresc i sec, allunyat de la llum solar directa i de temperatures extremes.
• Font d'alimentació: Always use a regulated 9V DC negative center power supply. Incorrect power can damage the unit.
• Connexions: Periodically check all cables and jacks for wear and tear. Replace damaged cables to prevent signal loss or noise.

7. Solució De Problemes

If you encounter issues with your PG-14 pedal, consider the following common troubleshooting steps:

• Sense so:
  • Comproveu totes les connexions dels cables (entrada, sortida, alimentació).
  • Assegureu-vos que la font d'alimentació estigui connectada correctament i que proporcioni un centre negatiu de 9 V CC.
  • Test with different cables, guitar, and amplifier per aïllar el problema.
  • Verify the pedal is engaged (LED indicator is on).
• Weak or Distorted Sound (unintended):
  • Check the power supply; insufficient power can cause poor performance.
  • Ensure instrument cables are not faulty.
  • Adjust the DRIVE and VOL knobs.
• Soroll/bruix excessiu:
  • Feu servir una font d'alimentació aïllada i d'alta qualitat.
  • Assegureu-vos de connectar a terra correctament el vostre amplificador i altres equips.
  • Move the pedal away from power transformers or other sources of electromagnetic interference.

8. Garantia i Suport

Per obtenir informació sobre la garantia i assistència tècnica, consulteu la pàgina oficial de JHS Pedals. weblloc web o contacteu directament amb el seu servei d'atenció al client. Conserveu el comprovant de compra per a qualsevol reclamació de garantia.

Visit the JHS Pedals Store: Botiga de pedals JHS a Amazon