1. Introducció i finalview
The APC AP9640 Network Management Card 3 is designed to provide remote monitoring and control capabilities for individual APC Uninterruptible Power Supply (UPS) units. By connecting the card directly to your network, it enables comprehensive management of your UPS system, enhancing reliability and operational efficiency.
This card facilitates direct network connectivity for your UPS, allowing for remote management without the need for a dedicated computer connection. It supports various environmental conditions, operating within a temperature range of 0 to 45 degrees Celsius and a relative humidity of 0 to 95%.
2. Configuració i instal·lació
Installing the APC AP9640 Network Management Card 3 involves inserting the card into a compatible APC UPS unit and connecting it to your network. Ensure the UPS is powered off before installation to prevent damage.
- Power Down UPS: Disconnect the UPS from the AC power source and ensure it is completely powered off.
- Localitza la ranura de la targeta: Identify the dedicated SmartSlot on your APC UPS. This is typically a rectangular slot on the rear panel.
- Insert Network Card: Carefully slide the AP9640 Network Management Card into the SmartSlot until it is firmly seated. Ensure the card's faceplate is flush with the UPS panel.
- Targeta segura: If applicable, use any provided screws or clips to secure the card in place.
- Connecteu el cable de xarxa: Connect a standard Ethernet cable from your network switch or router to the RJ-45 port on the AP9640 card.
- Power On UPS: Reconnect the UPS to the AC power source and power it on. The network card will initialize.
- Configuració inicial: Access the card's web interface via its assigned IP address (which can be obtained via DHCP or through the UPS's display, if available) to complete network settings and security configurations.
Figure 1: The APC AP9640 Network Management Card 3. This image shows the green circuit board with various components and the black faceplate featuring an Ethernet port and a USB-C console port. The card is designed to be inserted into a compatible UPS SmartSlot.
3. Operating the Network Management Card
The AP9640 card allows for comprehensive remote management of your UPS. Once installed and configured, you can monitor UPS status, configure settings, and receive alerts through a web browser or network management system.
- Web Accés a la interfície: Obre a web browser and enter the IP address of the AP9640 card. Log in with your configured credentials to access the management interface.
- Seguiment: View real-time UPS parameters such as battery charge, load, input/output voltage, i temperatura.
- Configuració: Adjust UPS settings, network parameters (IP address, DNS), user accounts, and security protocols.
- Registre d'esdeveniments: Review event logs and data logs to track UPS performance and identify potential issues.
- Alertes i notificacions: Configure email, SNMP, or other notification methods to receive alerts for critical events like power outages, bateria baixa o errors del sistema.
- PowerChute Network Shutdown: The card integrates with PowerChute Network Shutdown software, enabling graceful shutdown of connected servers and computers during extended power outages, preventing data loss.
4. Manteniment
Regular maintenance ensures the optimal performance and security of your AP9640 Network Management Card.
- Actualitzacions de firmware: Periodically check the APC website for firmware updates for the AP9640. Firmware updates can provide new features, security enhancements, and bug fixes. Follow the instructions provided by APC for safe firmware upgrade procedures. Note: Recent changes by the manufacturer may require a support contract for future firmware updates.
- Bones pràctiques de seguretat: Regularly change default passwords, use strong, unique passwords, and disable unused services to enhance security.
- Condicions ambientals: Ensure the UPS and the installed card operate within the specified environmental conditions (temperature, humidity) to prevent premature failure.
- Inspecció física: Occasionally inspect the card and its connections for any signs of damage or loose cables.
5. Solució De Problemes
This section provides solutions to common issues you might encounter with your AP9640 Network Management Card.
| Problema | Causa possible | Solució |
|---|---|---|
| Card not detected or no network connectivity. | Card not fully seated, faulty Ethernet cable, incorrect network settings, UPS not powered on. | Ensure the card is fully inserted. Check Ethernet cable connection and integrity. Verify network settings (IP, subnet, gateway). Confirm UPS is powered on. |
| No es pot accedir web interfície. | Incorrect IP address, network firewall blocking access, browser issues, card not initialized. | Verify the card's IP address. Check firewall settings on your network. Try a different web browser. Allow sufficient time for the card to initialize after power-up. |
| "The Application Is Incompatible With This APC OS" error. | Firmware incompatibility, corrupted settings. | Ensure the correct firmware version is installed for your card and UPS model. Consider resetting the card to factory defaults and reconfiguring. Some users have reported this issue related to email notification settings; try configuring other settings first. |
| Lenta web interface response. | Network congestion, outdated firmware, high load on the card. | Check network traffic. Update firmware to the latest version. Ensure the card is not overloaded with excessive logging or notification requests. |
If issues persist, consult the official APC support resources or contact their technical support for further assistance.
6. Especificacions
Key technical specifications for the APC AP9640 Network Management Card 3:
- Número de model: AP9640
- Dimensions del producte: 4.76 x 4.49 x 1.5 polzades
- Pes de l'article: 2.8 unces
- Temperatura de funcionament: 0 - 45 Degrees Celsius
- Humitat relativa de funcionament: 0 - 95 % (non-condensing)
- Elevació de funcionament: 0 - 3048 meters (0 - 10000 feet)
- Temperatura d'emmagatzematge: -5 - 45 Degrees Celsius
- Elevació d'emmagatzematge: 0 - 15240 meters (0 - 50000 feet)
- Connectivitat: Ethernet (RJ-45)
- Components inclosos: Targeta de xarxa
7. Garantia i Suport
For detailed warranty information, including terms and conditions, please refer to the official documentation provided by APC at the time of purchase or visit the APC by Schneider Electric Store or their official support website. Technical support and service options are available through APC's customer service channels.
Protection plans may also be available for extended coverage. Please check with your retailer for details on available protection plans.
