Yealink WMB-T5W Wallmount Bracket Instruction Manual for SIP-T53/T53W/T54W IP Phones

Introducció

This manual provides detailed instructions for the installation and proper use of the Yealink WMB-T5W Wallmount Bracket. This bracket is designed to securely mount compatible Yealink SIP-T53, SIP-T53W, and SIP-T54W IP phones to a wall, optimizing desk space and providing a stable platform for your communication device.

Contingut del paquet

Si us plau, verifiqueu que tots els components siguin presents abans de continuar amb la instal·lació.

• Yealink WMB-T5W Wallmount Bracket (1)
• Note: Mounting screws and wall anchors are typically not included and must be sourced separately based on your wall material.

Configuració i instal·lació

Follow these steps to properly install the Yealink WMB-T5W Wallmount Bracket and mount your IP phone.

1. Seleccioneu la ubicació de muntatge: Choose a suitable wall location that is sturdy enough to support the weight of the bracket and the IP phone. Ensure there is adequate space for cabling and user access.
2. Marca els punts de perforació: Hold the wallmount bracket against the wall at the desired height. Use a pencil to mark the positions for the mounting screws through the keyhole slots on the bracket. There are typically three keyhole slots: two at the top corners and one at the bottom center.
3. Perforar forats pilot: Using an appropriate drill bit for your wall material and chosen screws/anchors, drill pilot holes at the marked locations.
4. Inseriu ancoratges de paret (si cal): If drilling into drywall or other hollow materials, insert suitable wall anchors into the pilot holes.
5. Assegureu el suport: Align the keyhole slots on the bracket with the drilled holes/anchors. Insert and tighten screws, ensuring the bracket is firmly secured to the wall. Do not overtighten.
6. Prepare the IP Phone: Remove the desk stand from your Yealink SIP-T53, SIP-T53W, or SIP-T54W IP phone. Locate the mounting slots on the back of the phone.
7. Mount the IP Phone: Carefully align the mounting slots on the back of the IP phone with the corresponding tabs on the wallmount bracket. Slide the phone downwards onto the bracket until it clicks securely into place.
8. Adjust Hookswitch Tab: The bracket features an adjustable hookswitch tab. This tab prevents the handset from falling off when the phone is mounted vertically. Adjust its position as needed to securely hold the handset.

Imatge 1: The Yealink WMB-T5W Wallmount Bracket. This image displays the black plastic bracket with keyhole slots for wall mounting at the top and bottom, and internal tabs designed to secure a compatible Yealink IP phone. The adjustable hookswitch tab is visible at the bottom front.

Instruccions de funcionament

Once installed, the Yealink WMB-T5W Wallmount Bracket provides a stable and secure base for your IP phone. No specific operational steps are required for the bracket itself beyond ensuring the phone is correctly seated and the hookswitch tab is adjusted.

• Ensure the IP phone is firmly seated on the bracket.
• Verify the handset is securely held by the adjustable hookswitch tab when hung up.
• Connect all necessary cables (Ethernet, power) to the IP phone as per the phone's own instruction manual.

Manteniment

The Yealink WMB-T5W Wallmount Bracket requires minimal maintenance.

• Neteja: Utilitzeu un suau, sec o lleugerament damp cloth to wipe the surface of the bracket. Avoid abrasive cleaners or solvents, which may damage the finish.
• Inspecció: Periodically check the mounting screws to ensure they remain tight and the bracket is securely attached to the wall.

Resolució de problemes

If you encounter issues during installation or use, refer to the following common solutions.

• Bracket is not level: Ensure drilling points were marked accurately. Loosen screws slightly, adjust the bracket, and re-tighten. Use a spirit level during installation.
• El telèfon no encaixa bé: Verify that your IP phone model (SIP-T53, SIP-T53W, or SIP-T54W) is compatible with this bracket. Ensure the phone's desk stand has been removed and the phone is correctly aligned with the bracket's tabs before sliding it down.
• Handset falls off: Adjust the hookswitch tab to a position that securely holds the handset when the phone is mounted vertically.
• No mounting template included: While some wall mounts include a template, this model may not. Accurately measure and mark drilling points directly from the bracket itself. Alternatively, create a simple template by tracing the bracket's keyhole slots onto paper.

Especificacions

Informació de la garantia

Specific warranty details for the Yealink WMB-T5W Wallmount Bracket are not available in the provided product information. For warranty inquiries, please contact Yealink customer support or refer to the documentation provided with your original purchase.

Atenció al client

For further assistance, technical support, or product information, please visit the official Yealink weblloc o poseu-vos en contacte amb el seu departament d'atenció al client.

També podeu visitar el Yealink Store on Amazon per a més productes i informació.