1. Introducció
This manual provides essential information for the safe and effective installation, operation, and maintenance of your Okin Model 1.28.000.110.30 Deltadrive Series Motor. This motor is designed as a replacement actuator for electric recliner lift chairs.
Nota important de compatibilitat: It is crucial to verify that the motor SKU "1.28.000.110.30" on the product label and the shapes of the cable connectors/motor end are identical to your existing unit. This motor is not universally compatible and cannot replace other models.
2. Producte acabatview
The Okin Deltadrive Series Motor 1.28.000.110.30 is a low-voltage DC motor (24V) designed for quiet and safe operation in electric recliners. It features specific stroke and installation dimensions critical for proper function.
Figure 2.1: Okin Deltadrive Series Motor 1.28.000.110.30, showing the main unit and included pins.
2.1 Identifying Your Motor
Before installation, confirm the model number on the motor's label. The correct model number is 1.28.000.110.30.
Figura 2.2: Primer pla view de l'etiqueta del motor, destacant el número de model 1.28.000.110.30 i número de sèrie 19060860T 00029.
3. Especificacions tècniques
| Atribut | Valor |
|---|---|
| Número de model | 1.28.000.110.30 |
| Tipus de motor | Volum baixtagmotor de corrent continu (24V) |
| Actual | 2.2A |
| Freqüència d'operació | Encès 1 minut / Apagat 8 minut |
| Ictus | 250 mm |
| Dimensions mínimes d'instal·lació | 435 mm |
| Maximum Installation Dimensions | 685 mm |
| Aparença | Negre (PA), Blanc platejat (alumini) |
| Material | Alumini |
| Pes | 5.59 lliures |
| Connexions | 2 Pin Flat Round Power Transformer Connection, 5 Pin Hand Control Plug Connection |
Figure 3.1: Motor dimensions, illustrating the stroke and minimum installation size.
4. Instruccions d'instal·lació
Replacing your existing actuator requires careful attention to detail. Ensure the chair is unplugged from the power source before beginning installation.
- Preparació: Unplug the recliner from the wall outlet. Carefully flip the chair over or position it to access the existing motor and its connections.
- Desconnecta el motor antic: Disconnect the 2-pin flat round power transformer connection and the 5-pin hand control plug connection from the old motor. Note their orientation.
- Treure el motor antic: The old actuator is typically held in place by pins and locking springs at each end. Carefully remove these pins to detach the old motor.
- Instal·lar un motor nou: Position the new Okin Deltadrive motor in the same location as the old one. Secure it using the pins and locking springs. Ensure the motor is properly aligned.
- Connectar els cables: Connect the 2-pin flat round power transformer cable and the 5-pin hand control plug to the corresponding ports on the new motor. Ensure connections are secure.
- Gestió de cables: Use zip-ties or other appropriate fasteners to secure loose cables, preventing them from interfering with moving parts or becoming damaged.
- Longitud del cable d'alimentació: Be aware that the power cord may be short (approximately 1-2 inches long). An extension may be required depending on your setup.
Figure 4.1: Motor connections, illustrating the 2-pin power and 5-pin hand control plugs.
Figure 4.2: Detail of the motor's end connection point, where it attaches to the recliner mechanism.
5. Funcionament
Once installed, plug the recliner back into a power outlet. Use your recliner's hand control to operate the motor. The motor is designed for quiet and smooth operation.
- Reclinat: Press and hold the appropriate button on your hand control to extend the footrest and recline the chair.
- Returning Upright: Press and hold the appropriate button to retract the footrest and return the chair to the upright position.
- Cicle de treball: The motor has an operation frequency of "On 1 min / Off 8 min". This means it can operate continuously for up to 1 minute, followed by a mandatory 8-minute rest period to prevent overheating and ensure longevity. Adhering to this duty cycle is essential.
6. Manteniment
Regular maintenance helps ensure the longevity and optimal performance of your Okin Deltadrive motor.
- Neteja: Keep the motor and surrounding areas free from dust and debris. Use a dry cloth for cleaning. Do not use liquid cleaners directly on the motor.
- Comprovació de la connexió: Periodically inspect all cable connections (power and hand control) to ensure they are secure and free from damage.
- Parts mòbils: Ensure that no foreign objects obstruct the movement of the motor or the recliner mechanism.
- Lubricació: El motor generalment no necessita manteniment pel que fa a la lubricació interna. No intenteu lubricar els components interns llevat que us ho indiqui específicament el servei d'assistència d'Okin.
7. Solució De Problemes
If you encounter issues with your Okin Deltadrive motor, refer to the following common problems and solutions:
| Problema | Causa possible | Solució |
|---|---|---|
| Motor does not operate / No movement. |
|
|
| Motor jerks or does not move smoothly. |
|
|
| Chair does not hold position (e.g., reclines back when trying to stay upright). |
|
|
| El cable d'alimentació és massa curt. |
|
|
8. Garantia i Suport
For warranty information or technical support, please contact Okin customer service. Keep your purchase receipt and the motor's serial number (found on the label) readily available when contacting support.
Visit the official Okin Store for more information: Botiga Okin a Amazon
